Da-Lite Contour Electrol 지침서 - 페이지 5

{카테고리_이름} Da-Lite Contour Electrol에 대한 지침서을 온라인으로 검색하거나 PDF를 다운로드하세요. Da-Lite Contour Electrol 13 페이지. Installer friendly features
Da-Lite Contour Electrol에 대해서도 마찬가지입니다: 지침서 (9 페이지), 설치 관리자 매뉴얼 (2 페이지), 지침서 (4 페이지), 지침서 (8 페이지), 지침서 (8 페이지)

페이지 인쇄

1. Electrical Installation

SCREEN AdJUSTMENT FOR 120V SCREENS

1. Locate the wall switch and remove the cover plate from the

wall switch and remove the switch from the junction box.

2. Locate the two tactile buttons on the back of the switch.

They are black round buttons on silver plates. See 120V

Wiring Diagram.

3. To adjust the down limit switch, press and hold the down

tactile button until the LeD on the back of the switch turns

solid red. This will put the motor in limit set mode. Turn the

wall switch over and use the down button on the front of the

switch. Press and hold the down button until the desired

down position is reached. If you travel too far down, press

the up button to move the screen upward. If you press and

let go of either the up or down buttons, the motor will do a

small jog in that direction for fine adjustment of the screen.

once the desired position is reached, turn the switch over;

press and hold the down tactile button until the LeD on back

of switch blinks red twice. The down limit is now set.

NoTe: If the screen is in limit set mode and no buttons are

pushed for 20 seconds, the LeD on the back of the wall

switch will turn off, the motor will return to run mode and no

changes will be saved. If this occurs, return to step 3 for

down limit adjustment or step 4 for up limit adjustment.

SCREEN AdJUSTMENT FOR 220V/240V SCREENS WITH A BUILT-IN LOW VOLTAGE CONTROL

1. Remove the cover plate from the 3-button wall switch and

remove the switch from the junction box.

2. Locate small 3-position switch on back of wall switch. (See

Figure 11)

3. To adjust the down limit switch, slide the 3-position switch

to the down position. Press and hold the down button to

run the screen down to the desired stop position. Release

the button to stop the screen. Do NoT PUSH THe SToP

BUTToN.

4. When the screen is in the desired down position, slide the

3-position switch to the off (center) position. The down limit

switch is now set.

5. To adjust the up limit switch, slide the 3-position switch to

the up position. Press and hold the up button to run the

screen up to the desired stop position. Release the button

to stop the screen. Do NoT PUSH THe SToP BUTToN.

6. When the screen is in the desired up position, slide the

3-position switch to the off (center) position. The up limit

switch is now set.

7. To test limit switch setting, make sure the 3-position switch

4. To adjust the up limit switch, press and hold the up tactile

button until the LeD on the back of the switch turns solid

green. This will put the motor in limit set mode. Turn the

wall switch over and use the up button on the front of the

switch. Press and hold the up button until the desired up

position is reached. If you travel too far up, press the down

button to move the screen downward. If you press and let

go of either the up or down buttons, the motor will do a

small jog in that direction for fine adjustment of the screen.

once the desired position is reached, turn the switch over;

press and hold the up tactile button until the LeD on back of

switch blinks green twice. The up limit is now set.

5. To test the limit switch settings, press and release the up or

down buttons on the switch to operate the screen.

6. Replace the switch and cover plate on the wall.

iMportant note: The wall switch is ReQUIReD to make

any limit switch adjustments, even if a third party control

system is used. Therefore, it is advised to wire the switch or

provide a 3-conductor connection that is accessible.

Caution: Do not adjust for more drop than what was

ordered. at least 1-1/2 wraps of fabric must remain on

the roller. this screen comes standard with 0" or 2"

black at the top. see the specification data sheet for

details.

is in the off (center) position. Press and release the up or

down button on the wall switch to operate the screen.

8. Replace switch and cover plate on the wall.

NoTe: If stop button is pressed, the wall switch will reverse

direction. To correct this, press the stop button again. This

will reset the switch. You will have to re-set both the up and

the down settings.