Ekinex EK-FF1-TP 빠른 시작 매뉴얼 - 페이지 2

{카테고리_이름} Ekinex EK-FF1-TP에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Ekinex EK-FF1-TP 4 페이지. Binary output 16-fold / blind actuator 8-fold

페이지 인쇄

• Rated voltage (U

): 100-230 Vac 50 / 60Hz

• Rated current (I

): max 16 (10) A (both @ 100Vac and

@ 230Vac)

• Max switched power: max 4000 VA @ 250Vac

• Inrush current: 88 A 20 ms

Environmental conditions

• Operating temperature: - 5 ... + 45°C

• Storage temperature: - 25 ... + 55°C

• Transport temperature: - 25 ... + 70°C

• Relative humidity: 95% not condensing

Switching, display and connection elements

The device is equipped with a programming pushbutton

and a programming LED, membrane pushbuttons, LED

for status indication and terminals for connecting the KNX

bus line, the 110-230Vac power supply and the outputs.

Switching elements

• Pushbutton (3) for switching between the normal and

programming operating mode

• Pushbutton (7) for switching between the operating mo-

des: forced (pushbuttons on the front panel: active) or

automatic (pushbuttons on the front panel: not active)

• Pushbuttons (2) for forced operation of the output chan-

nels

EK-FF1-TP

16xD.O. 16(10)A/230Vac

50/60 Hz

8xBlind 16(10)A/230Vac

50/60 Hz

bus KNX

1) Terminal blocks for output channels

2) Pushbuttons for forced operation of the inputs

3) Programming pushbutton

4) Programming LED

5) Terminal block for KNX bus line

6) Terminal blocks for 230 Vac 50/60 Hz power supply

7) Pushbutton for switching between manual and automatic operation

8) LED for indication forced / automatic operation mode

9) LED for status indication of the outputs

Thanks to the pushbuttons located on the front of the de-

vice, the connected loads can be manually controlled in

the absence of voltage on the KNX bus or when the pro-

gramming has not yet been carried out, and in this way it

is possible to check the functioning of the loads. In these

conditions, however, it is not possible to have the status

feedback through the LEDs.

Note. In case of failure of the bus voltage, the

switching of the loads is possible only if they are still

powered with the mains voltage 110-230 Vac. The

relay status in case of failure and reset of the bus

can be set during the device configuration.

Display elements

• Red LED (4) for displaying the active operating mode of

the device (on = programming, off = normal operation)

• Green LEDs (9) for displaying the switching status of

the output channels (on = closed contact, off = opened

contact)

• Red LED (8) for displaying the operating mode (on =

forced operation, off = automatic operation)

230V~ 50/60Hz

Mounting

The device has degree of protection IP20, and is there-

fore suitable for use in dry interior rooms. The housing is

made for rail mounting according to EN 60715 in boards

or cabinets for electrical distribution. The installation is in

horizontal position, the correct position is when the KNX

bus terminal and the 110-230 Vac terminals are located at

the bottom and the terminals for the outputs are located

at the top.

For the installation of the device on the rail proceed as

follows:

• with the aid of a tool bring the locking device in the fully

lowered position (1);

• place the upper edge of the rear inner profile on the

upper edge of the rail (2);

• rotate the device towards the rail (3);

• push the locking device upward until it stops (4).

Before removing the device, be sure the inputs have been

disconnected and the bus terminal has been extracted

from its slot. Use a screwdriver to slide down the locking

device and remove the device from the rail.

Note. It is recommended that the installation of the

device always ensure the full accessibility of the

front side to allow the operation of the pushbuttons.

Connection of the KNX bus line

The connection of the KNX bus line is made with the ter-

minal block (black/red) included in delivery and inserted

into the slot of the housing.

Characteristics of the KNX terminal block

• spring clamping of conductors

• 4 seats for conductors for each polarity

• terminal suitable for KNX bus cable with single-wire

conductors and diameter between 0.6 and 0.8 mm

• recommended wire stripping approx. 5 mm

• color codification: red = + (positive) bus conductor,

black = - (negative) bus conductor

Warning! In order to supply the KNX bus lines use

only KNX bus power supplies (e.g. ekinex EK-AB1-

TP or EK-AG1-TP). The use of other power supplies

can compromise the communication and damage

the devices connected to the bus.

Connection of the 110-230 Vac power supply

The connection of the 110-230Vac power supply (fig. a) is

made with the screw terminals located on the lower front

of the device.