doona Lab SensAIert 빠른 시작 설치 매뉴얼 - 페이지 14
{카테고리_이름} doona Lab SensAIert에 대한 빠른 시작 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. doona Lab SensAIert 16 페이지.
Device reset
To reset the device, overturn SensAlert, open the zip and press the button in the
lower border
on the black box . Press and hold for 10 consecutive seconds.
Wait for the sound and press 3 more times quickly.
If you are the owner of the reset SensAlert, open the app, find the device in
question, press the settings icon and press "remove SensAlert".
Battery
SensAlert is powered by two CR2032 batteries (3 V), compliant with IEC 60086-4
standard. SensAlert's battery level can be monitored through the app. In case
of low level, the user can independently replace the battery. The new battery
must have the same characteristics and respect the correct polarity. To
replace the battery, the user must open the hinge and unscrew the small screw
located in the lower internal part. Flip the SensAlert over and lift the small black
lid. Replace the two batteries, paying attention to respect the correct polarity.
Close by repeating the operations in reverse order.
Lithium metal batteries
operating temperature: -20 to +60 C
EU Battery Directive 2006/66/EC, 2013/56/EU)
UN3091, Class9 (for the Air transport by PI969 Section II)
IATA Dangerous Goods Regulations Edition 62 (IATA DGR)
During the transportation of a large amount of batteries by ship, trailer or
railway, do not leave them in the places of high temperatures and do not allow
them to be exposed to condensation.
Warning:
Do not use different types of batteries as they can make the baby
safety device ineffective.
Do not let water penetrate into packaging boxes during their storage and
transportation.
Do not store the battery in places of high temperature or under direct sunlight.
Please also avoid places of high humidity.
Be sure not to expose the battery to condensation, extreme pressure, rain or
frozen conditions.
Do not short-circuit, deform, throw into fire or disassemble.
Charge according to the conditions specified.
Do not solder directly onto batteries.
Insert the battery correctly in electrical equipment.
Do not mix different type of batteries.
Do not ingest the battery, chemical burn hazard.
WARNING!
Warning:
This product contains a Button or Coin Cell Battery. A swallowed Button
or Coin Cell Battery can cause internal chemical burns in as little as two hours
and lead to death. Dispose of used batteries immediately. Keep new and used
batteries away from children. If you think batteries might have been swallowed
or placed inside any part of the body, seek immediate medical attention. the
product contains small parts or other characteristics that makes it unsuitable for
children. Serious injuries or death may occur.
Declaration of conformity
With the document herein, Doona warrants that SensAlert complies with the
seven essential requirements and the other relevant provisions established by
the 2014/53/EU Directive. According to the European Commission decision No.
2000/299/EC dated 04/06/2000, the frequency band used by this product is
harmonized throughout the EU countries. Therefore, this is a class 1 product and
can be freely used in all countries of the European Community.
Model: SensAlert
Contains FCC ID:QOQ-BGM220S2
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must ac-
cept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT: Changes or modifications not expressly approved by Doona could void the
user's authority to operate the equipment.
Industry Canada Statement
Contains IC:5123A-BGM220S2
This device complies with Idustry Canada license exempt RSS standard(s).
Operation is subject to the following two conditions:
1. this device may not cause interference, and 2. this device must accept any interference,
including interference that may cause undesired operation of the device.
THIS PRODUCT
IS IN COMPLIANCE WITH
EU DIRECTIVE 2012/19/EC.
separate disposal from domestic waste, must be taken to a differential waste collection center
for electric and electronic equipment or returned to the seller when a new, equivalent piece
of equipment is purchased. The user is responsible for handing over the piece of equipment to
the appropriate differentiating center at the end of its life cycle. Suitable differentiated waste
collection in prevision of the re-cycling of the decommissioned equipment and eco-compa-
tible disposal contributes to preventing possible negative consequences to the environment
and health and encourages the recycling of materials used to manufacture the product.
Unauthorized disposal of the product by the user entails administrative penalties pursuant to
Legislative Decree no. 22/1997 6 (Art.50 et seq. of Legislative Decree 22/97). For more infor-
mation on the collection systems available, please contact your local waste disposal service
or the shop where you purchased the product.
COMPLIANCE WITH EU DIRECTIVE
2006/66/EC AND SUBSEQUENT
AMENDMENTS.
the end of its useful life, these items need to be treated separately from household waste.
They must not be
disposed of as urban waste, but transferred to a waste disposal center for separate collection,
or returned to the retailer when purchasing new rechargeable and non-rechargeable batte-
ries. The possible chemical symbol Hg, Cd, Pb, placed under the crossed-out bin indicates the
type of substance contained in the battery, Hg = Mercury, Cd = Cadmium, Pb = Lead. Users
are responsible for providing the end-of-life batteries to the appropriate collection facilities in
order to facilitate treatment and recycling. The adequate separate collection for the subse-
quent forwarding of dead batteries for recycling, processing and environmentally compatible
disposal, helps to avoid possible negative effects on the environment and on human health
and promotes the recycling of substances contained in the battery. Unauthorized disposal
of the product by the user involves damage to the environment and human health. For more
information on the collection systems available, please contact your local waste disposal
service or the shop where you purchased the product.
ISO 7000-1641 (2004-01).
To identify the location where the operator's manual is stored or to identify information
that relates to the operating instructions. To indicate that the operating instructions
should be considered when operating the device or control close to where the symbol
is placed.
ISO 7000-0434 (2004-01)
To indicate that caution is necessary when operating the device or control close to
where the symbol is placed. To indicate that the current situation needs operator awa-
reness or operator action in order to avoid undesirable consequences.
The symbol of the crossed bin
shown on the equipment indi-
cates that, at the end of its life
cycle, the product requiring
T h e s y m b o l o f t h e c r o s -
sed - out bin shown on the
batteries or on the product
packaging indicates that, at