DoorHan DHRE-2 설치 및 운영 매뉴얼 - 페이지 2

{카테고리_이름} DoorHan DHRE-2에 대한 설치 및 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. DoorHan DHRE-2 3 페이지. External radio
DoorHan DHRE-2에 대해서도 마찬가지입니다: 설치 매뉴얼 (3 페이지), 설치 및 운영 매뉴얼 (3 페이지), 설치 및 운영 매뉴얼 (2 페이지)

페이지 인쇄

EC DECLARATION OF CONFORMITY

We: DoorHan Europe s.r.o.

Bozeny Nemcove 1689, 43201 Kadan, Ceska Respublika Herewith declare under sole

responsibility that:

• Declares that: The device model Reciever outside 433MHz 2 chan-

nels (DHRE-2)

• Сomplies with the essential safety requirements of the following

directives:

73/23/EEC and subsequent amendment 93/68/EEC

89/336/EEC and subsequent amendment 92/31/EEC

and 93/68/EEC

Additional note:

These products have undergone tests in a typical uniform configuration

(all products manufactured by DoorHan Europe s.r.o.)

01/03/2010

Date

1. FUNCTION

External receiver DHRE-2 is intended for receiving a radio signal of the remote control

panel at 433MHz frequency, decoding and control signal (NO) generation for controlling

electric operators.

2. OVERALL DIMENSIONS

А = 63 мм

В = 90 мм

С = 25 мм

3. TECHNICAL SPECIFICATIONS

Operating frequency, MHz

Power supply voltage (DC), V

Useful current, mA

Max. number of panels per one channel, pc

Number of channels, pc

Operating temperature, °С

Actual versions

4. CONNECTION

1. You should connect this device to a power supply 12/24V DC using terminals

+24V and GND.

2. You should connect electric operator control contacts to radio receiver output ter-

minals CH1 or CH2.

5. PROGRAMMING

1. Receiver memory clearance. After you have switched on power supply, you should

press and hold a panel programming button «CODE1» or «CODE2», depending on the

channel you wish to clear. A short beep will sound. The indicator «LED1» will go on for

10 seconds, then it will go out, and a long beep will sound acknowledging the erasure of

memory programmed codes.

2. Programming of Doorhan panels in the receiver. For panel programming you should

press and release a panel programming button «CODE1» or «CODE2», depending on the

channel you wish to program. The red indicator A will go on and a short beep will sound.

You should press the selected button (which you later on wish to use for unit control) on

the panel twice within 10 seconds when the red indicator «LED1» is on. The indicator A

will go out and a short beep will sound, meaning the successful programming of the panel

code in the receiver memory.

Note:

• 3 long beeps will sound when there is the receiver memory overflow.

3. Setting of several panels. For setting several panels you should repeat item 2 for

each new panel.

6. REMOTE PANEL PROGRAMMING

Within the interval of 1 - 4 seconds you should act as follows:

1. You should press and hold button 2 (see Figure) of the programmed panel.

2. You should press and hold button 1, not releasing the pressed button 2.

3. You should release all pressed buttons.

4. You should press the programmed panel button; the receiver will enter the panel

programming mode. A short beep will sound.

Note:

• After you have entered the programming mode the panel programming is possible

within 8 seconds, after these 8 seconds expire the receiver will quit the programming

mode.

5. You should press the button, which you later on will use for receiver channel control,

on a new panel twice. A short beep will sound, meaning the programming of the panel

code in the receiver memory.

Note:

• 3 long beeps will sound when there is the receiver memory overflow.

• It is necessary to perform panel programming within the receiver range.

• A number of the button can be defined by points on a panel body.

DoorHan thanks you for purchasing our products. We hope that you will remain satisfied

by quality of this product. If you have any questions on purchasing, distribution and

servicing, please contact our regional representatives' offices or company headquarters at

the address:

Czech Republic, Kadan, 43201, Kralovsky VRCH 2018.

Phone: +420-474-319-111, сell: +420-607-508-343, e-mail: [email protected],

OPERATION MANUAL FOR

EXTERNAL RECEIVER DHRE-2

Mikhail Kiselev

Open

Ch1

Ch2 +24GND

web: www.doorhan.cz

INSTALLATION AND

Managing Director

signature

433

12/24

110

-40..+55

soft - v 1.0

pcb - v 1.0

12VDC

- +