Air Design CSV24N 설치, 사용자 및 유지 관리 매뉴얼 - 페이지 15

{카테고리_이름} Air Design CSV24N에 대한 설치, 사용자 및 유지 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Air Design CSV24N 19 페이지. Water cassettes csvn series; hcvn series

페이지 인쇄

- if the room temperature is above 26°C the appliance will start the cooling cycle.

This will continue until the temperature drops below 24°C.

FAN SPEED ADJUSTMENT When the FAN button is pressed, one of the

following fan speeds can be selected: AUTO - HIGH - MED - LOW. In the AUTO

mode, the electronic control automatically selects the fan speed according to

the difference between the set temperature and the room temperature. This

function automatically increases the fan speed if a greater cooling or heating

effect is required.

SLEEP MODE Access this mode by pressing the SLEEP button. The symbol

will appear on the display, as shown in the drawing to the side. The SLEEP

mode automatically adjusts the temperature to make the sleeping environment

more comfortable during the night. During the cooling or dehumidifying modes

the set temperature is increased gradually by 2°C during the first two hours of

operation. During the heating mode the set temperature is decreased gradually

by 2°C during the first 2 hours of operation. Timed switching off can also be set

together with the SLEEP mode.

SETTING THE CLOCK Press the CLOCK button and the corresponding part

of the display starts to blink. Set the actual time using the HR (hour) and MIN

(minute) buttons. Once this operation has been completed, confirm the setting

by pressing the SEND button and listen for the beep to make sure that the

appliance has received the signal.

IMPORTANT: Before setting timed switching on, set the required operating mode

and fan speed. Then switch the air conditioner off.

TIMED SWITCHING ON To set timed switching on, the appliance must be off.

Press the START button and the corresponding part of the display starts to blink.

Set the time for timed switching on using the HR and MIN buttons. The subsequent

switching off time may also be set by pressing the STOP button and setting the

required time using the HR and MIN buttons. Confirm the new setting by pressing

the SEND button and listen for the beep to make sure that the appliance has

INSTALLATION, USE AND

MAINTENANCE GUIDE

WATER CASSETTES

received the signal.

Fig. 36

TIMED SWITCHING OFF To set timed switching off, the appliance must be on

or the timed switching on function must be set. Press the STOP button and the

corresponding part of the display starts to blink. Set the time for timed switching

off using the HR and MIN buttons. The subsequent switching on time may also

be set by pressing the START button and setting the required time using the

HR and MIN buttons. Confirm the new setting by pressing the SEND button and

listen for the beep to make sure that the appliance has received the signal.

Fig. 37

WARNING! Once the switch on and/or the switch off time is expired, it will be

automatically canceled from the internal memory. Switch on and switch off time

need to be setted each time the user necessitate.

AIRFLOW ADJUSTMENT The SW button activates the louvres and the airflow

is directed alternately upwards and downwards to obtain even distribution

throughout the room.

N.B.: During cooling they should be positioned horizontally. During heating they

should be directed downwards (as hot air tends to rise).

WALL-MOUNTED CONTROL: CD2/X7

Fig. 38

DRY

HEAT

SLEEP

Fig. 39

Selects the operating mode in the order given below: FAN (fan), COOL

(cooling), DRY (dehumidifying), HEAT (heating), AUTO (automatic operation)

Sets the required temperature between 18°C and 30°C. The temperature

is increased by pressing

FAN Selects the fan speed in the order given below: AUTO (automatic), H

(high), M (medium), L (low)

WARNING!

Do not position the louvres manually

as this may damage the delicate

mechanism that moves them.

POWER

TIMER

SLEEP

COMP

COOL

MODE

FAN

MODE

TEMP

FAN

SLEEP

CLOCK

MIN

START

STOP

and .

Fig. 40

Fig. 41

Fig. 42

Fig. 43