Air Design CSV24N 설치, 사용자 및 유지 관리 매뉴얼 - 페이지 17

{카테고리_이름} Air Design CSV24N에 대한 설치, 사용자 및 유지 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Air Design CSV24N 19 페이지. Water cassettes csvn series; hcvn series

페이지 인쇄

COOL

The writing COOL appears on the air-conditioner control display. The unit

operates in the air-conditioning mode.

- the zone valve starts if Troom Tset+1

- the zone valve stops if Troom Tset

In any case activation of the zone valve is subject to 3 minutes delay each

time it stops.

DRY

The writing DRY appears on the air-conditioner control display. The unit

operates in the dehumidifying mode to reduce the percentage of humidity

in the room.

HEAT

The writing HEAT appears on the air-conditioner control display.

The unit operates in the air-conditioning mode.

- the zone valve starts if Troom Tset+1

- the zone valve stops if Troom Tset

In any case activation of the zone valve is subject to 3 minutes delay each

time it stops.

AUTO

The writings COOL and HEAT appear on the display simultaneously.

Temperature setting

The setting temperature can be set in the range of 18°C-30°C by pressing

TEMP

and TEMP

buttons. The LCD on the display unit will show the

setting temperature.

Louvre swing (optional)

Press the SW button to start/stop louvre swing.

Louvre direction adjustment (optional)

Press the LV button to change the angle of the louvres (which are controlled

by the louver motor):

- if the button is pressed and released, the angle of the louvres is changed

very slightly.

- if the button is pressed and held, the angle of the louvres continues to

change until the button is released;

SLEEP

Press the SLEEP button to start the sleep function. The

on the display. In the cooling mode, the set temperature is automatically

raised by 1°C after one hour. Similarly in the heating mode, the temperature

is decreased by 1°C after one hour.

ROOM TEMPERATURE

23.0

22.0

SLEEP MODE START

Note:

- when the system is set in the SLEEP mode, press the SLEEP button to

cancel the function;

- when the system is set in the SLEEP mode and the TEMP button is

pressed, it increases the temperature from the last setting by 1°C;

- when the system is set in the SLEEP mode and the cassette is turned off

(also due to power failure), the

Clock

To set the clock:

Press the button until the display blinks;

Press the HR button to set the hour;

Press the MIN button to set the minutes;

Press the again. The time display stops blinking.

Automatic start

The cassette can be programmed in advance to switch on.

Press the START button until the time in the START section of the display

blinks;

Press the HR button to set the hour;

INSTALLATION, USE AND

MAINTENANCE GUIDE

symbol appears

COOLING MODE

Increase of 1°C

after 1 hour

Fig. 48

HOURS

SLEEP function is cancelled.

WATER CASSETTES

Press the MIN button to set the minutes;

Press the START button again. The display stops blinking.

To cancel this function, press the START button again.

Automatic stop

The cassette can be programmed in advance to switch off.

Press the STOP button until the time in the STOP section of the display blinks;

Press the HR button to set the hour;

Press the MIN button to set the minutes;

Press the STOP button again. The display stops blinking.

To cancel this function, press the STOP button again.

WARNING! Once the switch on and/or the switch off time is expired, it will be

automatically canceled from the internal memory. Switch on and switch off time

need to be setted each time the user necessitate.

TIPS FOR BEST USE

Connect the cassette to a dedicated power socket protected by a

magnetothermal circuit breaker of suitable capacity for the electrical input

of the appliance.

When the water cassette starts or stops, especially in the heating mode,

creaking sounds may be heard. This is caused by thermal expansion of the

unit parts.

Mist may sometimes be produced by the cassette for a few seconds in the

cooling mode. This is quite normal and is caused by the difference in

temperature between the air flowing out of the appliance and the air in the

room.

Do not place heat sources near to the cassette as this could deform the

plastic parts.

Do not insert objects into the air intakes or outlets when the cassette is in

operation.

Do not place objects in a position that may obstruct the passage of the air

into the unit as this could affect appliance efficiency.

ENERGY SAVING

Do not open or close doors and windows too often. Constant exchange of

heat with the outside affects the working of the appliance.

Do not set too high a temperature (in the heating mode) or too low (in the

cooling mode).

Do not install the appliance where it is exposed to direct sunlight.

Use the TIMER for the timed switching on of the appliance, to avoid the

cassette operating needlessly while you are out of the house.

Use the SLEEP function during the night.

ROUTINE MAINTENANCE

ATTENTION!

Turn off the automatic circuit breaker before carrying out any cleaning

operations. Use a cloth dampened with lukewarm water (max 40°C) and

mild detergent to clean the cassette. Do not use solvents or harsh detergents.

OPENING THE PANEL

To open the grille turn the plastic screws present on the grille by 90° (1/4 of a

turn) (fig. 49) and gently pull the panel downwards without forcing the hinges

that fasten it to the appliance. Attention: to make cleaning easier, the grille may

be removed completely since the receiver panel is positioned on the fixed frame

of the unit (see fig. 50).

Fig. 49

Fig. 50