Canon PIXMA MP750 사용자 설명서

{카테고리_이름} Canon PIXMA MP750에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Canon PIXMA MP750 2 페이지. Photo multifunction printer
Canon PIXMA MP750에 대해서도 마찬가지입니다: 보충 설명서 (6 페이지), 빠른 시작 매뉴얼 (49 페이지), 빠른 시작 매뉴얼 (48 페이지)

페이지 인쇄
Canon PIXMA MP750 사용자 설명서
Thank you for purchasing the Canon PIXMA MP780/750. To prepare your machine for use, please follow these
Easy Setup Instructions before referring to any other documentation.
IMPORTANT
Do not connect the USB cable until after the software is installed. See the rear side of this sheet for details.
1
Unpack and install the machine.
Check the package contents.
• Machine
MP780
MP750
• Ink tanks
Black
BCI-3eBK
• Easy Setup Instructions • Quick Start Guide
• Setup CD-ROM
The Setup CD-ROM contains the MP Drivers, as well as the User's Guide, Software Guide and Photo
Application Guide in electronic format. Please read these guides.
• In this sheet, illustrations of MP780 are shown.
• A printer cable is not included. You must purchase a USB cable (less than 16 3/8 ft.) to connect your
machine to a computer.
2
Connect the telephone line. (MP780 model only)
Connect the telephone line and any necessary external device.
For details, see the Quick Start Guide.
Connect the telephone
line cord to the wall jack.
You can connect an external
device (telephone or answering machine) if necessary.
3

Connect the power cord.

1
Connect the power cord.
1. Connect one end of the power cord to the rear of the machine.
2. Connect the other end to the AC outlet.
2
If the message <PUT IN CARTRIDGE> appears, go to Step 4, "Install the print
head."
4

Install the print head.

1
Press the Open Button to open the
Paper Output Tray. Then lift the
Scanning Unit until it locks into place.
IMPORTANT
Be sure to hold the Scanning Unit firmly with one
hand.
2
Open the two Inner Covers.
(2) The Print Head Holder moves to the center.
(3) Install the print
head here.
(1) Open the two
Inner Covers.
4
Prepare the print head.
Do not touch!
Remove the protective cap and discard it.
Start Here
Easy Setup Instructions
• Power cord
• Telephone line
• Print head
Black
BCI-6BK
Cyan
BCI-6C
Magenta BCI-6M
Yellow
BCI-6Y
Connect external devices as follows:
External device jack
Telephone line jack
Telephone or answering machine
Telephone or
Telephone
answering machine
Machine
line
Built-in computer modem and telephone
LINE TEL
Telephone
Telephone
Machine
Computer
line
Lift the Scanning
Press the Open Button.
Unit.
Click
Pull
the Scanning
Unit Lever.
3
Raise the lock lever.
Touch only the lock lever!
Raise this securely.
5
Insert the print head.
(2) Push back.
(1) Insert.
6
Lower the lock lever.
5

Install the ink tanks.

1
Prepare the ink tanks.
Remove the orange-colored
protective film. If it is not
removed completely,
problems with printing
may occur.
2
Insert the ink tanks.
Click
Push it in until locks
into place.
3
Close the Inner Covers and the Scanning Unit.
Click
Close the two Inner Covers.
6

Load the paper.

1
Open the Auto Sheet Feeder.
2
Load two sheets or more of letter-size plain paper.
(1) Open the Auto Sheet
Feeder.
(2) Pull out the Paper
Support until it stops.
7
Align the print head from the Operation Panel.
Be sure to align the print head to ensure print quality.
1
Press [OK] to start print head alignment.
(1) This message appears.
ALIGN PRINT HEAD
PRESS [OK]
If this message
does not appear
after closing the
Scanning Unit,
see "Aligning
The Print Head
Automatically"
in the Quick Start
Guide.
If the printed pattern matches the illustration, print head alignment is complete.
You can change the language displayed on the LCD.
For details, see "Selecting The Language For The LCD" in the Quick Start Guide.
You have completed installation and alignment.
If you are connecting the machine to a computer for use, see the rear side of this sheet for
instructions on installing the software.
© 2004 Canon U.S.A., Inc., Canon and BCI are registered trademarks and PIXMA is a trademark of Canon Inc.
All other products and brand names are registered trademarks or trademarks of their respective owners.
Specifications subject to change without notice.
HT7-0029-000-V.1.0
xx2004A
Click
Lower the lock lever
until you hear a click
as it locks into place.
Remove the protective cap
and discard it.
Do not touch!
Good example
Bad example: Tank 6BK is
not fully inserted.
Make sure to press it down
firmly.
Click
Pull the Scanning Unit Lever
towards you to close the
Scanning Unit.
IMPORTANT
Be sure to hold the Scanning Unit firmly with one hand.
Load the paper with the print side face up.
Pinch and adjust
the paper guide
to the width of
the stack.
Ensure the paper stack
does not exceed the paper limit mark.
(2) Press [OK].
(3) The machine will print
the print head position
pattern and automatically
align the print head.
© CANON INC. 2004
PRINTED IN CHINA