DACE LUX DC12 설치 및 사용 설명서 - 페이지 3

{카테고리_이름} DACE LUX DC12에 대한 설치 및 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. DACE LUX DC12 12 페이지.

페이지 인쇄

Auxiliary Light

LUX DC12

The Auxiliary Light output is

Control Board

used to connect an external light

to the operator. The external

light can be switched on when

the operator is triggered for a

preselected period of me (up

to 9 minutes) or the light can be

ac vated via a dedicated remote

bu on, without triggering the

operator. If switched on by a

External

dedicated bu on, it will remain

Light

on for a period of 1 hour but can

be switched oﬀ before 1 hour is

up by pressing the same bu on

again.

Refer to 'Se ng Auxiliary

Output....Menu 5' for

programming.

Solar panels must be mounted in direct sunlight and the

•

panel angle alignment should be adjusted for op mal

condi ons for the loca on. It is very important to ensure

that no shadows will cross the panel during the day.

It is recommended that a ba ery with a capacity of at least

•

7Ah is used.

The operator will automa cally detect that it is connected

•

to a solar supply once the panel voltage exceeds 17V DC. It

will then no longer indicate a power fail message but will

only display a single bar "_" when the panel output voltage

is too low for charging.

When connec ng a solar panel directly to the controller

•

the transformer must be removed from the input.

Solar Panel specs:

Power Ra ng:

20W min

Min Voltage output:

17V DC

Max Voltage Output:

22V DC.

ERROR

MEANING

CODE

Cause:

Low ba ery voltage. The ba ery may be faulty or an excessive number of

opera ons, or devices, may have drained the ba ery.

Remedy:

Ensure the operator is plugged in and switched on. Fully charging a 5Ah 12V

Low Ba ery

ba ery will take 24hrs if the operator is not in use and if no other devices, such as

locks; receivers & lights, are connected.

Check that connected devices are not drawing excessive currents.

Addi onal devices will reduce the number of daily opera ons and standby

opera ons.

Cause:

The operator is not detec ng an input supply voltage.

Remedy:

If using a transformer, ensure that the transformer is plugged in and switched on.

The output voltage should be between 12VAC – 18VAC, if not the transformer may

Power Fail

need to be replaced.

If using a solar panel, ensure the output voltage is between 17VDC - 22VDC. When

a solar panel is connected to the operator it is necessary for the DC voltage to be

higher than 17V for the operator to switch to DC Solar Opera on a er which the

operator will stop showing the Power Fail message.

LIMITS

REV

AUX LOCK 12V TRIG INF GND

DACE

Relay Module

COM

Code: SA001

CONNECTING A SOLAR PANEL

REV

AUX LOCK

12V TRIG INF GND

LUX DC12 Control Board

Not Polarity

Sensi ve

Solar Panel

ERROR CODES

CAUSE & REMEDY

Thank you for choosing Dura Access Control Equipment (DACE). We welcome you to the ever growing interna onal

community of DACE product owners. The advanced engineering and high-quality construc on of each DACE

product we build is something of which we are proud.

The LUX DC12 garage operator is packed with features to bring you convenience and enhance your security.

Power

Input

Your owners manual will introduce you to the features and opera on of your new LUX DC12. It is suggested that

you read it carefully since the informa on it contains can contribute greatly to the sa sfac on you receive from

your new garage door operator.

Important informa on before automa ng your garage door!

Only automate garage doors that are within speciﬁca on and are in good working order. The door must be able

●

to be opened and closed using only one hand and, if released midway, the door should not move. The force

used to open the door by hand should be similar to that used to close the door. If the door is not in perfect

working order, it should be serviced by a qualiﬁed garage door technician prior to automa on.

Automa ng a garage door increases the risk of entrapment and crushing. While all reasonable steps have been

●

taken to ensure that your garage door operator is safe to install and operate, it must be noted that a garage

door is a heavy piece of equipment and can cause serious injury and death. Never allow children to play with or

around the garage door. Only ac vate the garage door when it is in full view and when there are no children or

Power

animals in close proximity that could get injured.

Input

We highly recommend the installa on of Infrared Safety Beams to increase the safety of the doors opera on.

●

The LUX DC12 is not waterproof and is therefore not suitable for outdoor use.

●

It is important to note that the LUX DC12 garage operator is ba ery operated and by simply switching oﬀ the

●

mains power supply to the operator it does not mean that the operator does not have power. It is therefore

important that both the mains power supply and the ba ery be disconnected before working on the operator.

Use extreme cau on when opera ng the manual release as the door may move, resul ng in injury or damage.

●

The door should be inspected every 6 months by disengaging it from the operator and moving it by hand. The

door should move easily but it should not close on its own if released. If the door is found to be defec ve, it

must remain disconnected from the operator and a qualiﬁed garage door technician be called to carry out

repairs to the door.

Please a ach your invoice to this manual for future use (see warranty)

Dura Access Control Equipment reserves the right to make changes to the products described in this manual

without no ce and without obliga on to no fy any persons or organisa ons of such revisions or changes.

Addi onally, DACE makes no representa ons or warran es with respect to this manual.

This manual may only be copied or distributed as a whole, no altera ons or subsec ons may be distributed or

copied without the prior express consent of DACE in wri ng

FOREWORD

DISCLAIMER