Canon CN-E20-50mm T2.4 L FP 운영 매뉴얼

{카테고리_이름} Canon CN-E20-50mm T2.4 L FP에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Canon CN-E20-50mm T2.4 L FP 3 페이지. Digital cinema lens

페이지 인쇄

Digital Cinema Lens

CN-E20-50mm T2.4 L F / CN-E20-50mm T2.4 L FP

CN-E45-135mm T2.4 L F / CN-E45-135mm T2.4 L FP

ENG

OPERATION MANUAL

Before using the product, make sure to read the "GENERAL SAFETY INFORMATION" and be sure to use the

product correctly.

This product comes with the following documents:

• Operation Manual "Before Using The Product" (Included with the product)

• Operation Manual "Regulations" (Included with the product)

• Operation Manual (Web)

• Depth-of-field (Web)

PRODUCT LIST

Make sure all of the following items are included in the packing box. If you find any item missing, please

contact your dealer or Canon Inc.

① Lens body

② Lens cap

③ Rear lens cap

④ Attachment holder

⑤ Operation Manual "Before Using The Product"

⑥ Operation Manual "Regulations"

②

The illustrations in this manual show CN-E20-50mm T2.4 L F unless otherwise specified.

The shapes of product may vary depending on models and specifications.

MOUNTING AND CONNECTING

For PL mount, read the following instructions before mounting the lens.

1. The PL mount supports Cookeʼs /i Technology, so make sure that the camera is set to "/i".

2. Do not mount the lens if the camera is set to a mount communication mode other than "/i". Doing so

could result in malfunction.

A variety of professional camera accessories are available using Φ15 mm and Φ19 mm rod adaptors.

(When using a Φ19 mm rod, attach the supplied attachment holder to the lens holder.)

Note

1. Before mounting the lens on the camera, make sure that the power of camera and the power of supply

equipment are turned off.

2. Be sure to use the lens holder when mounting the lens on a camera. Be sure to avoid applying

excessive weight to the lens mount when the lens is mounted on a lens support.

1. Attach the lens to the camera tightly so that both mounting surfaces are

in complete contact.

Note

For details on how to attach the lens, refer to the camera's

operation manual as well.

2. Secure the attachment holder on the lens support using the clamping

screw supplied with the lens support.

3. Push the lens toward the camera until both mounting surfaces are in

complete contact and clamp the lens support to the rods.

BT1-D002-B-ENG

⑥

①

④

③

Lens support

NAMES OF PARTS

Focus drive gear

Attachment holder

⑤

BACK FOCUS ADJUSMENT

If the image formation plane of the lens and the focal plane of the camera are not aligned, the image will not be

in focus when zooming, resulting in out-of-focus images.

F.B. Adjusting Screw (Gold)

F.B. Adjustment

Fixing Screw (Black)

F.B. Adjuster

* CN-E20-50mm T2.4 L F / CN-E20-50mm T2.4 L FP：approx. 0.9-1.8 m, 3-6 ft

CN-E45-135mm T2.4 L F / CN-E45-135mm T2.4 L FP：approx. 1.8-3.7 m, 6-12 ft

Zoom drive gear

Iris drive gear

F.B. Adjuster

Lens holder

LEMO 4-pin

Connector

PL mount lenses are equipped with a LEMO 4-pin connector.

It connects to external devices that support Cookeʼs /i Technology.

1. Open the rubber cap of F.B. adjuster and loosen the

F.B. adjusting fixing screw (black) using the standard

screwdriver.

2. Select an object at an appropriate distance*.

Use any object with sharp contrast to facilitate the

adjustment work.

3. Set the iris fully open.

4. Set the lens to the telephoto angle by turning the zoom

ring.

5. Bring the object into focus by turning the focus ring.

6. Set the lens to the widest angle by turning the zoom ring.

7. Turn the F.B. adjusting screw (gold) with a standard

screwdriver to focus.

8. Repeat steps 4 to 7 a few times until the object is

brought into focus both at the widest end and the

telephoto end.

9. After the back focus adjustment is completed, tighten the

F.B. adjusting fixing screw. Then close the rubber cap.

EF mount

(F type)

PL mount

(FP type)

1/3