Air Hogs Havoc Heli 사용 설명서 - 페이지 4

{카테고리_이름} Air Hogs Havoc Heli에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Air Hogs Havoc Heli 4 페이지.
Air Hogs Havoc Heli에 대해서도 마찬가지입니다: 사용 설명서 (4 페이지)

페이지 인쇄

Tip!

OPERATION

- Your helicopter will be auto-protected while the helicopter crash into other obstacles, you need to switch ON/OFF button to ON again to

restart the helicopter.

- Don't operate the helicopter under the direct sun or strong lighting; it will affect the control system of your helicopter.

- Don't cover the lens of the transmitter. No signal will be released while you cover the lens.

- Don't stick any other label onto the helicopter; the other label will affect receiving of IR signal.

Tip!

CONTROLLING

- For controlling the sticks on transmitter, try not to push the sticks immediately to the extreme position. It should be like steering a bicycle rather than

pressing computer game sticks.

- For the novice Pilot (after the trimming procedure was completed), it is highly recommended to focus exclusively on learning to control the Throttle

stick first. Even if the helicopter may turn around a bit by itself, there is no need to keep it straight and keep it fly nicely. For the first flight, it is

important to learn to keep the helicopter at a constant altitude of around 1 meter with small inputs on the Throttle stick. Once the Pilot masters this,

he may start learning to take control with the direction stick.

Tip!

SAFETY

- Read through the whole instruction Manual before starting to play your helicopter.

- This product is designed to be used only indoors. Do not use it outdoors unless in windless days without any small gusts of wind.

- Never fly in a place cluttered with obstacles (place full of furniture, people, pets etc.)

- Make sure you and other people keep 1-2 meters away from the helicopter while you start for flight.

- Always keep an eye on the flying helicopter to prevent it flying, landing or crashing on or near your head, your body and any other people.

- Never disassemble or attempt to modify the product. It may damage the product and cause danger.

- Never put hands or face close to rotating parts. Doing so create the risk of unexpected injury. To avoid such risk, never operate this product while

sitting on the floor or on a chair. Operate this product in a posture that allows you to quickly get out of the way if necessary.

- Always switch off both the flying unit and transmitter when leaving transmitter unattended. If the power switch is left on, it is possible that

unintended stick operation occurs, when the transmitter is placed on a floor or a chair.

- Never allow young children to use this product. Doing so creates the risk of accidents caused by the rotating parts.

- Never use parts that are damaged or have altered shape in this product to ensure safe practice.

Tip!

TRIMMING

- The helicopter can be out of trim after some severe or multiple crashes, improper storage or changing of temperature... etc.

You can simply solve this problem following the below procedures.

i) If the helicopter takes too much forward speed by itself

ii) If the helicopter takes too much backward speed by itself

Trouble Shooting

Symptom

Propeller can't move.

Suddenly stop and drop down when flying.

The helicopter does not react.

Loss of control.

For further questions and problem, please visit our website www.airhogs.com.

Spin Master Ltd., 450 Front Street West, Toronto, ON M5V 1B6 Canada

Spin Master Inc., PMB #10053, 300 International Drive, Suite 100, Williamsville, NY 14221, USA

Spin Master Toys Far East Limited. Rm #1113, 11/F, Chinachem Golden Plaza, 77 Mody Rd.,

Tsimshatsui E., Kowloon, HK

Spin Master Toys UK Ltd., Meadowbank, Furlong Road, Bourne End, Bucks, SL8 5AJ,

United Kingdom

Spin Master France – 36 rue de Silly – 92100 Boulogne Billancourt – France

North American Consumer Information

Phone: 1-800-622-8339

www.spinmaster.com

Step 1:

Take the tail

between fingers.

Step 1:

Take the tail

between fingers.

- ON/OFF Switch is OFF.

- Weak Battery.

- Weak power.

- Channel selection on transmitter is not correct.

- Another Infrared control device using the same

channel.

- Affected by strong lighting.

Step 2:

Twist tail anti

clockwise for

about 30°.

Step 2:

Twist tail

clockwise for

about 30°.

Cause

Conforms to product safety standards ASTM F963-03,

EN71 regulatory requirements. Products and colors may

vary. Please retain this information for future reference.

Patent Pending. MADE IN CHINA.

44290-20007609-ENG-IS-R1(0) REV 1

Correction

- Set switch to ON.

- Re-charge the battery pack.

- Reset the correct channel.

- Avoid these if possible, or choose another place to operate the

helicopter.

- Change another environment to avoid direct lighting.

Step 3:

Release.

90°

Step 3:

Release.

90°