ADVANCE Easy Moving M-TANK 조립, 사용 및 유지보수 매뉴얼 - 페이지 8

{카테고리_이름} ADVANCE Easy Moving M-TANK에 대한 조립, 사용 및 유지보수 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ADVANCE Easy Moving M-TANK 17 페이지.

Motorized Tank

7 INSTALLATION

It is the installer's responsibility to verify the presence of any risk of danger in the installation

area and to determine the suitability in accordance with both the applicable laws and the product

characteristics described in this manual.

Only specialized technical personnel are authorized to do the installation and maintenance of the product.

All operations must be carried out following the accident prevention regulations and in compliance with

safety warnings.

If you ﬁ nd any damage, anomalies or shortcomings in the product, do not proceed with the installation

and immediately contact your dealer.

The motorized tank must be installed in a covered place, where the temperature is between 0 and 40

° C and the relative humidity is between 40 and 80%, it must not be placed on damp walls and must

not be exposed to the elements, it must be installed levelled and placed on a solid and smooth ﬂ oor to

facilitate the adjustment of the feet.

The motorized tank must be connected to the fuel release dispenser (accessory on request) (see ﬁ gure

1) using rigid or ﬂ exible antistatic pipes, the pipes must have the minimum number possible of elbows,

they should have a minimum radius of 30 cm, while the maximum vertical gap allowed for the fuel transport

pipe is 3 m and the total length of the pipes must not exceed 5 m (each).

All hose connections and junctions must be closed with steel hose clamps to ensure a perfect airtight seal.

Before ﬁ nally positioning the storage unit, complete it by ﬁ tting the sensor, already equipped with a

ﬂ ange, by inserting it into the hole on the side of the storage unit, inserting the sealing gasket (see ﬁ gure

6). Also install the four adjustable feet in their respective threaded inserts on the bottom of the warehouse.

The dispenser (accessory on request, see ﬁ gure 5) must be installed on the boiler tank to reﬁ lled. The

magnetic contact sensor called REED, applied to the dispenser's exhaust door,

via an electrical connection to the motorized warehouse, will check the correct functioning of the conveyor

system. The magnetic contact sensor will also ensure that the fuel transport system is turned off if the tank

to be reﬁ lled is full (see the dispenser instruction manual).

8 PIPES CONNECTION

For connections between the motorised tank and the dispenser, it is essential to use rigid steel or ﬂ exible

pipes with an internal diameter of 50 mm. All pipe junctions must be sealed airtight and must therefore

be carefully tightened. No oblique sections, only vertical or horizontal sections should be made. Very

long sections must be carefully ﬁ xed to the wall or to resistant supports; all elbows must have a minimum

radius of 30 cm. Connect the Ø 50 mm pipe from the OUT outlet to the connection on the dispenser

called OUT, connect the Ø 50 mm pipe from the IN outlet to the connection on the dispenser called IN.

Fuel will ﬂ ow through the IN pipe, while only air and dust will ﬂ ow through the OUT pipe.

All the pipe sections used for the transport system must be antistatic in order to guarantee the effective

dispersion of static currents and must be connected to an grounding point in the electrical system (see

ﬁ gure 1). The grounding point of the motorised tank (see ﬁ gure 2) must be connected to an grounding

point of the electrical system.

ﬁ gure 1

ﬁ gure 2

OUT air outlet

Grounding point

IN fuel intake

15/12/21 Rev:1.0.1