Douglas Lighting Controls WORXID2-DPR-L 설치 매뉴얼

{카테고리_이름} Douglas Lighting Controls WORXID2-DPR-L에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Douglas Lighting Controls WORXID2-DPR-L 2 페이지. Diversa occupancy & vacancy sensors - recessed ceiling, passive infrared (pir), 24vac

페이지 인쇄

Installation Guide

PART NO.

FEATURES

WORSID1-N-N

• Commercial grade components for long term reliability

standard lens, PIR, 24Vac,

1-pole

• Straightforward wiring for quick installation

WORXID1-N-N

extended lens, PIR, 24Vac,

• Factory configured for the most common applications

1-pole

WORSID2-DPR-L

• DIP switches and dials for advanced functionality

standard lens, PIR, 24Vac,

2-pole, dimming, photo,

• Options:

relay, low temp.

WORXID2-DPR-L

•

Standard, Extended, High-Bay Lens

extended lens, PIR, 24Vac,

•

Dimming, Photo Sensor, Isolated Relay

2-pole, dimming, photo,

•

Low Temperature/High Humidity

relay, low temp.

WORBID2-DPR-L

high-bay lens, PIR, 24Vac,

2-pole, dimming, photo,

relay, low temp.

Operation

Diversa 24Vac (low voltage) sensors are powered by 24Vac from either the Diversa Series Power Pack (WP-PP20-***)

or a 24Vac transformer. When in operation, the sensor will detect initial motion using PIR; once motion is detected,

the sensor and Power Pack (or connected diode pulse relays) contacts will close. Motion through Passive Infrared

(PIR) is used to maintain the occupied condition as long as occupants remain within coverage pattern of Sensor.

Sensor Location Guidelines

To optimize the performance of Diversa Sensors, please review the coverage pattern, range, and model to

match with the application. Room dynamics will change when people and furniture are occupying the space.

In some rooms, after move in, some sensors may require adjustments.

• Ensure that the sensor is at least 30 inches away from air handlers/registers and not pointed directly at

windows

• Check that you are installing the right product (check the product model number) as per the drawings

Sensor Location Guidelines for "P" models

• Place outside the direct cone of light from fixtures

• Between 3 to 12 feet from windows

• As close as possible to the fixture being controlled

• Above the least illuminated space in the work area

• Away from lighting that is not being controlled by the sensor

SPECIFICATIONS

Power

• 24Vac

25%

• Class 2 low voltage source

• 60Hz

• Use #18AWG wire

Outputs

• Diode Pulse: Each output is capable of driving up to four Diode

Pulse relays

• 0-10V Dimming: Connections are polarity-sensitive - up to 25mA

sinking

• Isolated Relay: SPDT Form C contact rated for 1A at 30Vdc

Power Consumption

• 9.5mA Standard

• 14.0mA with Auxiliary Relay

Approvals

• FCC

Environment

• Indoors, stationary, non-vibrating, non-corrosive atmosphere and

non-condensing humidity

• Ambient Operating Temperature: 32°F to 104°F (0°C to 40°C)

• Storage Temperature: -14°F to 140°F (-25°C to 60°C)

Diversa by Douglas Lighting Controls

Diversa Occupancy & Vacancy Sensors - Recessed Ceiling, Passive Infrared (PIR), 24Vac

Line Voltage Passive Infrared (PIR) Occupancy / Vacancy Sensor

(Shown with cover

plate removed)

Light Level Dial

Used to determine light

level for Photo Functions

Grey (-)

0-10V Dimming

(Only models with Dimming)

Wiring

Instructions

The WOR Series Low Voltage sensors are equipped with #22AWG Leads. Use appropriate sized wire nuts to

connect the wires to the incoming load terminations.

Wiring to a Power Pack

(2-pole sensor requires 2-pole Power Pack)

DIMENSIONS/MOUNTING inches (mm)

Unit attaches to mounting ring with

•

screws or it can be mounted into an

octogan box.

Ceiling tile

Mounting

0.88"

Wire

(2 2 )

ring

2.0"

(52)

4.17"

3 0 ° Tilt

(106)

DIPs and Dials

under cover

plate

•

The WOR sensor will fit an octagon

box. It is very important that conduits

be attached at opposite ends of the

box.

Conduit

Octagon Box

•

Use a 2 1/8 " or more, deep box.

If the box is less, use the spacer ring.

DIP Switches

Manual Override Button

Test Mode LED

Time Delay Dial

Ranges from 30s to 30 min.

Full turn Clockwise for Auto Time

Full turn Counterclockwise for Test Mode

Auto Time LED

Violet (+)

Blue

Return

Red

Orange

Primary Output Pole

Red/White

Yellow/White

Yellow

Yellow/Black

Sensor Link

COM

Secondary Output Pole

WP-PP20-D

Black

White

Black

White

Red

Orange

Sensor

Link

Override / Multi-Level Switching

www.douglaslightingcontrols.com

Installation

Standard Lens (S)

• Locate the sensor near the entrance door wall to prevent it from viewing out into the hallway.

• The lens can tilt, allowing the sensor to be pointed toward the area in front of the entrance door.

• Positioning the sensor in this manner ensures that an occupant moves across the longest detection beam

upon entrance, utilizing the sensor's maximum PIR range.

• Designed for a mounting height of 7-15 ft

White

24Vac

Typical Enclosed O ce

Extended Lens for Larger Rooms (X)

• Place the sensor near the center of the room ceiling. Locate it so the approximate distance of 27ft in

or in dead center of room.

• Tilt the lens to aim the detection zone to the bottom of the door.

• Positioning the sensor in this manner ensures that the beam does not reach outside the room without

reducing sensitivity.

• Optimal usage is to detect large motions such as walking.

• Designed for a mounting height of 7-15ft.

27ft

Typical Classroom

High Bay Lens for High Ceiling Applications (B)

• For 15 to 40 foot ceilings

• Position sensor based on ceiling height, beam pattern

and coveage requirements

14040200-C

Top View

14 ft

7 ft

0 ft

7 ft

14 ft

Side View

9 ft

0 ft

14 '

12 ' 10 '

6 '

3 '

0 '

3 '

6 '

10 '

12 '

14 '

Top View

27 ft

14 ft

0 ft

14 ft

27 ft

Side View

9 ft

0 ft

27 '

16 '

9 '

3 '

0 '

3 '

9 '

16 '

27 '

Top View

40 ft

18 ft

0 ft

18 ft

Side View

40 ft

20 ft

10 ft

0 ft

40 '

30 '

20 '

10 '

0 '

10 '

20 '

30 '

40 '