Bosch ASCENTA SHX6AP 사용 및 관리 매뉴얼 - 페이지 13

{카테고리_이름} Bosch ASCENTA SHX6AP에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch ASCENTA SHX6AP 21 페이지. Bosch ascenta models dishwashers use & care manual
Bosch ASCENTA SHX6AP에 대해서도 마찬가지입니다: 사용 및 관리 매뉴얼 (21 페이지), 사용 및 관리 매뉴얼 (26 페이지)

페이지 인쇄

OPERATING THE:

SHE4AM0

SHE4AM1

WARNING

You could be seriously scalded if you allow hot water to splash

out of the dishwasher. OPEN THE DOOR CAREFULLY during any

wash or rinse cycle. Do not fully open the door until water noises

have stopped.

To Start Unit:

• Door must be closed. Press the "ON/OFF" button to turn the unit

on.

• One of the Wash Cycle Indicator Lights will be flashing to show

you are in the Wash Cycle selection mode.

• Press the "<" or ">" button to select the desired wash cycle.

• If desired select the "HALF LOAD" or DELAY START" features at

this point.

o if you would like to delay the start time of the dishwasher press

the "DELAY" button until the desired delay time (3/6/9 hrs.)

shows on the indicator lights.

o in addition to your Wash Cycle selection, for small loads of

lightly soiled dishes press the "HALF LOAD" button. This will

save energy and water (sHe4aM1# only).

• Press the "START" button to begin the cycle (Wash Cycle Indica-

tor Light will stop flashing and the "Active" Indicator Light will

illuminate)

note: rinse agent indicator light will be illuminated if the unit needs

rinse agent.

Child Lock

• After pressing the "START" button you can activate the Child Lock

feature.

• Press and hold down the "<" button until Child Lock Indicator Light

illuminates (light goes out when button is released).

• Now any button you press (except ON/OFF) will not function and

the Child lock indicator light illuminates when pressing.

• To deactivate, press and hold the "<" button until the Child Lock

indicator light goes out.

To Cancel the Cycle:

• Press and hold the "START/RESET" button until the "Active" Indica-

tor light goes out.

• Wait for about 1 minute for the dishwasher to drain.

• Press the "ON/OFF" button.

SET" button, then release the ">" button.

• The "Clean" Indicator Light and at least one addition Indicator Light

will be flashing to show you are in the Options Setup Mode.

• Press the ">" button to select the option you would like to adjust

o If the "CLEAN" and "RINSE AGENT" Indicator Lights are flashing

you are ready to set the amount of rinse agent the unit will

dispense.

o If the "CLEAN" and "SANITIZED" Indicator Lights are flashing you

are ready to turn your extra Dry Heat option on/off.

To Set the Amount of Rinse Agent Dispensed

note: if your glasses have spots you need more rinse agent. if your

glasses have streaks you need less rinse agent.

• With the "CLEAN" and "RINSE AGENT" Indicator Lights flashing.

• Press the "<" button to change the amount of Rinse Agent Dis-

pensed.

• As you press the "<" button you will notice the Wash Cycle Indica-

tor lights illuminating

o if none of the Wash Cycle indicator lights are illuminated, the

rinse agent Dispenser is turned off.

o if one of the Wash Cycle indicator lights are illuminated, the

rinse agent Dispenser is set to deliver the lowest charge of

rinse agent.

o if two of the Wash Cycle indicator lights are illuminated, the

rinse agent Dispenser is set to deliver a medium charge of

rinse agent.

o if three of the Wash Cycle indicator lights are illuminated, the

rinse agent Dispenser is set to deliver the largest charge of

rinse agent.

• Press "START" to save your settings.

To Turn the Extra Dry Heat On or Off

• With the "CLEAN" and "SANTITIZED" Indicator Lights flashing.

• Press the "<" button to change the Extra Dry Heat setting.

• As you press the "<" button you will notice the Wash Cycle Indica-

tor lights illuminating

o if none of the Wash Cycle indicator lights are illuminated, the

extra Dry Heat option is turned off.

o if one of the Wash Cycle indicator lights are illuminated, the

extra Dry Heat is turned on.

• Press "START" to save your settings.

• You are now ready to start a new

cycle

note: You cannot cancel a cycle with the

Child lock feature activated.

Setting Options (Rinse Agent

Amount / Extra Dry Heat Activa-

tion)

• Door must be closed. Press the "ON/

off" button to turn the unit on.

• One of the Wash Cycle Indicator Lights

will be flashing to show you are in the

Wash Cycle selection mode.

• To enter the Options Setup Mode,

press and hold down the ">" button,

then press and release the "START RE-