Bosch ASCENTA SHX6AP Use And Care Manual - Page 13
Browse online or download pdf Use And Care Manual for Dishwasher Bosch ASCENTA SHX6AP. Bosch ASCENTA SHX6AP 21 pages. Bosch ascenta models dishwashers use & care manual
Also for Bosch ASCENTA SHX6AP: Use And Care Manual (21 pages), Use & Care Manual (26 pages)
Print Page
OPERATING THE:
SHE4AM0
SHE4AM1
WARNING
You could be seriously scalded if you allow hot water to splash
out of the dishwasher. OPEN THE DOOR CAREFULLY during any
wash or rinse cycle. Do not fully open the door until water noises
have stopped.
To Start Unit:
• Door must be closed. Press the "ON/OFF" button to turn the unit
on.
• One of the Wash Cycle Indicator Lights will be flashing to show
you are in the Wash Cycle selection mode.
• Press the "<" or ">" button to select the desired wash cycle.
• If desired select the "HALF LOAD" or DELAY START" features at
this point.
o if you would like to delay the start time of the dishwasher press
the "DELAY" button until the desired delay time (3/6/9 hrs.)
shows on the indicator lights.
o in addition to your Wash Cycle selection, for small loads of
lightly soiled dishes press the "HALF LOAD" button. This will
save energy and water (sHe4aM1# only).
• Press the "START" button to begin the cycle (Wash Cycle Indica-
tor Light will stop flashing and the "Active" Indicator Light will
illuminate)
note: rinse agent indicator light will be illuminated if the unit needs
rinse agent.
Child Lock
• After pressing the "START" button you can activate the Child Lock
feature.
• Press and hold down the "<" button until Child Lock Indicator Light
illuminates (light goes out when button is released).
• Now any button you press (except ON/OFF) will not function and
the Child lock indicator light illuminates when pressing.
• To deactivate, press and hold the "<" button until the Child Lock
indicator light goes out.
To Cancel the Cycle:
• Press and hold the "START/RESET" button until the "Active" Indica-
tor light goes out.
• Wait for about 1 minute for the dishwasher to drain.
• Press the "ON/OFF" button.
SET" button, then release the ">" button.
• The "Clean" Indicator Light and at least one addition Indicator Light
will be flashing to show you are in the Options Setup Mode.
• Press the ">" button to select the option you would like to adjust
o If the "CLEAN" and "RINSE AGENT" Indicator Lights are flashing
you are ready to set the amount of rinse agent the unit will
dispense.
o If the "CLEAN" and "SANITIZED" Indicator Lights are flashing you
are ready to turn your extra Dry Heat option on/off.
To Set the Amount of Rinse Agent Dispensed
note: if your glasses have spots you need more rinse agent. if your
glasses have streaks you need less rinse agent.
• With the "CLEAN" and "RINSE AGENT" Indicator Lights flashing.
• Press the "<" button to change the amount of Rinse Agent Dis-
pensed.
• As you press the "<" button you will notice the Wash Cycle Indica-
tor lights illuminating
o if none of the Wash Cycle indicator lights are illuminated, the
rinse agent Dispenser is turned off.
o if one of the Wash Cycle indicator lights are illuminated, the
rinse agent Dispenser is set to deliver the lowest charge of
rinse agent.
o if two of the Wash Cycle indicator lights are illuminated, the
rinse agent Dispenser is set to deliver a medium charge of
rinse agent.
o if three of the Wash Cycle indicator lights are illuminated, the
rinse agent Dispenser is set to deliver the largest charge of
rinse agent.
• Press "START" to save your settings.
To Turn the Extra Dry Heat On or Off
• With the "CLEAN" and "SANTITIZED" Indicator Lights flashing.
• Press the "<" button to change the Extra Dry Heat setting.
• As you press the "<" button you will notice the Wash Cycle Indica-
tor lights illuminating
o if none of the Wash Cycle indicator lights are illuminated, the
extra Dry Heat option is turned off.
o if one of the Wash Cycle indicator lights are illuminated, the
extra Dry Heat is turned on.
• Press "START" to save your settings.
• You are now ready to start a new
cycle
note: You cannot cancel a cycle with the
Child lock feature activated.
Setting Options (Rinse Agent
Amount / Extra Dry Heat Activa-
tion)
• Door must be closed. Press the "ON/
off" button to turn the unit on.
• One of the Wash Cycle Indicator Lights
will be flashing to show you are in the
Wash Cycle selection mode.
• To enter the Options Setup Mode,
press and hold down the ">" button,
then press and release the "START RE-
13