Bosch FAP-OC 500Series 설치 매뉴얼 - 페이지 5

{카테고리_이름} Bosch FAP-OC 500Series에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch FAP-OC 500Series 28 페이지. Built-in wall ovens
Bosch FAP-OC 500Series에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (21 페이지), 사용 설명서 지침 (40 페이지), 설치 매뉴얼 (6 페이지), 제품 정보 (40 페이지), 설치 매뉴얼 (28 페이지), 사용자 설명서 (48 페이지), 사용자 설명서 (48 페이지), 설치 매뉴얼 (28 페이지), 사용 및 관리 매뉴얼 (44 페이지), 설치 매뉴얼 (32 페이지), 사용 및 관리 설명서/설치 지침 (40 페이지), 빠른 참조 매뉴얼 (4 페이지), 사용 및 관리 매뉴얼 (27 페이지), 설치 매뉴얼 (24 페이지), 설치 매뉴얼 (32 페이지), 사용 및 관리 매뉴얼 (24 페이지), 서비스 매뉴얼 (41 페이지), 사용 및 관리 매뉴얼 (21 페이지), 설치 매뉴얼 (32 페이지), 서비스 매뉴얼 (36 페이지), 설치 매뉴얼 (32 페이지), 빠른 시작 및 안전 매뉴얼 (13 페이지)

페이지 인쇄
Bosch FAP-OC 500Series 설치 매뉴얼

Before you begin

Tools and Parts Needed

Philips head screwdriver
▯
1/8" drill bit and drill
▯
Measuring tape
▯

Parts Included

Built-in oven

Power Requirements

The outlet must be properly grounded in accordance with
all applicable codes.
The electrical outlet for the appliance must either be
▯
located in the shaded area A or outside of the area
where the appliance is installed.
Secure any unsecured units to the wall using a
▯
standard bracket B.

Removing Packaging

NOTICE: To prevent damage to your floor keep the unit
in its packaging base until ready to be placed in the
cabinet opening. Do not slide the unit across the flooring.
Cut straps on outside of box.
1.
Remove cardboard box.
2.
Remove all top and side cardboard and Styrofoam
3.
braces.
Place oven in front of cabinets where it is to be
4.
installed.
B e f o r e y o u b e g i n

Preparing the units

This unit must be installed according to all installation
▯
instructions to ensure its safe operation.
Check the appliance for damage after unpacking it. Do
▯
not connect the appliance if it has been damaged in
transit.
Proceed in accordance with the installation sheets for
▯
installing accessories.
Before starting up the appliance, remove any
▯
packaging material and adhesive film from the
cooking compartment and the door.
The cabinet into which the appliance is built in must be
▯
heat-resistant up to 195° F (90 °C), and adjacent
cabinet fronts up to 160° F (70 °C).
Do not install the appliance behind a decorative panel.
▯
There is a risk of overheating.
Any cut-outs that need to be made in the units should
▯
be made before the appliance is installed. Remove
any shavings, as they may prevent the electrical
components from working properly.
Wear protective gloves to prevent cuts. Parts that are
▯
accessible during installation may have sharp edges.
Secure any unsecured units to the wall using a
▯
standard bracket.
The dimensions in the figures are in inches (mm).
▯
5