Draper Silhouette/Series E 설치 및 운영 지침

{카테고리_이름} Draper Silhouette/Series E에 대한 설치 및 운영 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Draper Silhouette/Series E 5 페이지. Electric projection screen
Draper Silhouette/Series E에 대해서도 마찬가지입니다: 설치 및 운영 지침 (5 페이지)

페이지 인쇄

220V Silhouette/Series E & V Electric Projection Screen by Draper

1 Read instructions through completely before proceeding; keep them for

future reference. Follow instructions carefully. Installation contrary to

instructions invalidates warranty. Care in mounting and correct operation

will mean long and satisfactory service from your Draper screen.

2 Screen should be accessible for complete removal should fabric become

damaged or should other service be required.

3 Screen should be installed level (using a carpenter's level).

4 Nothing should be fastened to screen dowel or viewing surface.

5 Operating switch(es) packed separately in screen carton. Do not discard

with packing material.

6 Screen operates on 220V AC, 50 hz., 1 ph. current.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

These instructions are meant as a guide only. They do not imply any

responsibility on the part of Draper, Inc. for improper installation or faulty

workmanship at the jobsite.

Installation

Your Draper screen can be mounted on a wall or suspended from the ceiling,

or mounted on 15cm or 25-36cm extension brackets. Extension brackets must

be ordered separately from Draper. With each method of installation, the case

must be mounted level and with the flat back parallel to the wall.

To reduce the risk of personal injury, use only the hardware which comes with

the screen or is specified in these instructions.

The screen (or extension brackets) should be mounted into studs or blocking

in the wall/ceiling, or in drywall (minimum thickness 13 mm [

fied anchors. For any other type of installation, follow all local building and

safety codes.

Steel studs, concrete or cinder block walls and all other types of non-wood

frame construction require the use of special screws or anchors. The selection

of appropriate mounting hardware should be made by a qualified professional

installer.

When locating viewing surface and checking clearance for screen's operation,

remember surface is centered in case.

Take care to install wall/ceiling electrical box and conduit so they will be fully

concealed by the screen case after installation.

Handle case carefully to avoid scratching.

Regardless of mounting method, screen should be positively and securely

supported so that vibration or even abusive pulling on the viewing surface will

not cause case to work loose or fall. Installer must insure that fasteners used

are of adequate strength and suitable for the mounting surface chosen.

Wall Mounting

Mount two, three or four aluminum brackets provided ("Z" Clips) on the wall

at desired height, using appropriate fasteners. Verify that they are in line and

level to fully engage with the mounting lip on back of screen case. 42 mm of

free space is required above the "Z" Clips to allow case lip to be engaged over

the lip of the "Z" Clips.

Engage the lip on back of screen case with lip of "Z" Clip and gently pull down

to fully engage case to brackets.

Form SilhouetteE&V220V_Inst14-R

Installation/Operating Instructions

Caution

"]) with speci-

Printed in U.S.A.

Lip on back of case

"Z" Clip

(wall mounting bracket

supplied with Silhouette)

Ceiling/Suspended Mounting

Locate two offset ceiling brackets (supplied) and slide these into the chan-

nel on top of screen case by aligning the chamfered edges of each bracket

parallel to the channel length. Allow bracket to drop against bottom of channel

and then rotate bracket counter-clockwise. Slide one bracket to each end of

screen case until it stops against end cap of case. Tighten two set screws

to lock bracket in place. Make sure that the flange of the ceiling bracket that

has four holes is extended beyond the end caps of the case. Repeat above

procedure for second ceiling bracket, making sure to slide it towards opposite

end of case.

To mount against ceiling, hold screen case against ceiling and mark mount-

ing hole locations. Each bracket has two holes towards the front edge and

two holes towards the back edge. Installer must use at least two fasteners

per bracket with one fastener in one of the two holes closest to back edge

of bracket, and one fastener in one of the two holes closest to front edge of

bracket. Installer must insure that fasteners are of adequate strength and suit-

able for the mounting surface chosen.

(front of Silhouette case)

To mount suspended from ceiling, the brackets need to be installed on

screen case as noted on page one. Attach "S" Hooks (supplied) through the

holes in the brackets. Select the set of holes that allows the screen to hang

in a vertical position. The installer is to provide the materials and fasteners

to attach the "S" Hooks to the ceiling. Installer must insure that the fasteners

and suspension material is of adequate strength and suitable for the mounting

surface chosen.

If you encounter any difficulties installing or servicing your Silhouette screen, call your dealer or

Draper, Inc. Spiceland, Indiana, U.S.A., telephone (765) 987-7999 or fax (765) 987-1689.

US Patent Nos. 5,296,964; 6,111,694

Silhouette fully engaged

on "Z" Clip

Ceiling bracket in

channel of case

Ceiling bracket

Mounting fasteners

(supplied by others, 2 per bracket)

(right end of Silhouette case)