Draper FlexShade 설치 및 운영 지침 - 페이지 6

{카테고리_이름} Draper FlexShade에 대한 설치 및 운영 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Draper FlexShade 12 페이지. Exterior clutch-operated shade
Draper FlexShade에 대해서도 마찬가지입니다: 설치 및 운영 매뉴얼 (8 페이지), 설치 지침 (2 페이지), 사용 설명서 (12 페이지), 설치 및 작동 지침 (11 페이지), 설치 및 운영 지침 (16 페이지), 설치 및 운영 지침 (4 페이지), 사용 설명서 (7 페이지), 설치 및 운영 지침 (12 페이지), 설치 및 운영 지침 (16 페이지)

페이지 인쇄

Dual Roller Coupled Motorized FlexShade

Section 5 - Mounting / Assembly

PERSONNEL

REQUIRED

Please Note: Custom products/installations may not be reflected by this document. Call Draper

product installation.

Section 5.1 - Operating the Retractable Coupler Shaft

Please Note: Custom products/installations may not be reflected by this document.

The Draper

Coupled FlexShade

and link panels together. The retractable coupler shaft has three distinct positions: fully extended,

intermediate, and fully retracted.

1. To retract the coupler shaft from fully extended to the intermediate position, grasp the roller

with one hand while rotating the metal ring counterclockwise

approximately ½ of a turn with the other; this will leave the shaft extended approximately ½"

2. To retract the coupler shaft fully, rotate the metal ring counterclockwise (as viewed facing the

coupler assembly) an additional 1/3 turn.

3. To lock shaft in place when extended, rotate metal ring clockwise ¼ turn.

Please Note: There is no retractable shaft in

the idler end assembly on the idler end shade

. This idler assembly

(furthest from the operator)

utilizes a sliding pin and retainer clip.

Section 5.2 - Operator-end Bracket Assembly

1. Before mounting shades, verify measurements on the card provided with the shade, and ensure the brackets are installed at the correct width.

2. Measure and mark wall, jamb, or ceiling for placement of mounting brackets. Mark a level line across all windows to ensure a level installation.

Mark the outer edges of the operator- and idler-end brackets, and the center locations of the coupler brackets. Locations are determined by:

A. Operator-end panel width;

B. Intermediate panel width

C. Idler-end panel width.

3. Mount the operator-end bracket assembly

. Ensure the outside edge is aligned with

bracket types)

the marked location.

Please Note: Installer is responsible for selecting

mounting hardware appropriate for site conditions.

Caution: Wear gloves that are flexible enough to

adjust the metal wheel but strong enough to prevent

scrapes from surrounding metal or other surfaces.

Section 5.3 - First

(Operator-end)

1. If desired, the proper location of the coupler bracket assembly can be verified. Otherwise, proceed to step 2.

A. Installer #1 attaches

the operator end to the

operator-end bracket.

2. Install first coupler bracket assembly to mounting surface.

3. Ensure the operator-end fabric/roller assembly's coupler shaft is completely retracted

(see "Operating the Retractable Shaft" and Fig.5)

4. Raise first rear/upper fabric/roller assembly into place.

Installer #1 inserts operator end of fabric/roller assembly into operator-end bracket.

Installer #2 lifts the coupler end up next to the coupler bracket assembly, then extends

the coupler shaft to the intermediate position by rotating the ring clockwise 1/3 of a turn

(see "Operating the Retractable Shaft" and Fig. 5)

installation of the next panel.

5. Connect power so the shade can be operated and adjusted.

6. Operate the shade to ensure proper fabric tracking and to set up and down limits

on limit adjustment and field adjustments)

7. Raise shade to upper limit.

(Requires two (2) installers)

Caution:.Installation of this product requires two people.

Caution: Before beginning installation, practice extending and retracting the coupler shaft in a fabric/roller assembly, following

instructions in the "Operating the Retractable Coupler Shaft" section below.

Caution: All motors should be tested and limits set using test cord before electrician wires shade.

(Fig. 5)

utilizes a locking retractable shaft to hold roller assemblies in place

Please Note: These instruction steps are for installing brackets one at a time. Brackets may also all

be installed at the same time, prior to installing roller/fabric assemblies. If brackets are installed first,

please be certain of measurements and locations. For best results, assemble the unit on a flat, clean

surface and verify measurements before attaching brackets.

(Fig. 6)

; and

(s)

Figure 6

(Fig. 6 for

Fabric Roller Assembly

(Fig. 7)

B. Installer #2 slides the coupler bracket

onto the coupler shaft of the fabric/roller

assembly to be installed, and holds in place.

. This will hold the first unit in place during

(Extra Large Hardware)

(as viewed facing the coupler assembly)

(13mm)

C o u

p l e

r B

C. Verify and mark location

and set fabric/roller

assembly aside.

(see sections

, Inc. with any questions about

Figure 5

r a c

k e t

F R O

N T

page 6 of 12

Figure 7