Draper FlexShade 설치 및 운영 지침 - 페이지 2
{카테고리_이름} Draper FlexShade에 대한 설치 및 운영 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Draper FlexShade 16 페이지. Exterior clutch-operated shade
Draper FlexShade에 대해서도 마찬가지입니다: 설치 및 운영 매뉴얼 (8 페이지), 설치 지침 (2 페이지), 사용 설명서 (12 페이지), 설치 및 작동 지침 (11 페이지), 설치 및 운영 지침 (12 페이지), 설치 및 운영 지침 (16 페이지), 설치 및 운영 지침 (4 페이지), 사용 설명서 (7 페이지), 설치 및 운영 지침 (12 페이지)
페이지 인쇄
FlexShade
®
PLEASE READ - Important Installation Information
Caution:
1. Inspect all boxes to make sure you have
received the proper shades and parts.
Crank may be shipped separately, or in
same carton as shades.
2. Open cartons lengthwise, taking care not
to cut into cardboard shipping container.
PLEASE READ - Safety Information
Important Safety Information
Improper installation and use of the FlexShade
cise installation, mishandling of the shade during installation or installation on an insufficient wall or ceiling structure. Please use extreme care.
1. Please read the following installation guidelines thoroughly and follow them carefully. Failure to do so may cause product to fall or otherwise fail, and could result in
serious injury.
2. Installation and calibration of the shade should only be performed by an authorized, qualified, and experienced professional.
3. Do not affix the unit to wall or ceilings that have inadequate strength to permanently hold the unit during use. It is the owner's and installer's responsibility to
confirm the wall or ceiling to which the unit attaches is sufficient to permanently hold the weight and stress loads of the unit at all times. Draper
responsible for improper installation, application, testing, or workmanship related to the product at place of installation.
4. It is the installer's responsibility to make sure appropriate fasteners are used for mounting.
5. All brackets, fascia, headboxes, pockets, wall clips, and other hardware must be installed level. Shade unit must be level and square.
6. Never leave the area while operating the shade during installation, maintenance, or normal operation, unless it is secure and safe.
7. Before testing or operation, carefully inspect the entire area and path of the shade and areas underneath the shade to be sure no persons or objects are in the area.
8. During testing or operation, carefully watch the surrounding area for any potential safety concerns including nearby persons or objects.
9. After installation, the entire system should be carefully tested to ensure safe and normal operation. Extreme care should be taken during testing to remain clear of
moving parts to avoid possible injury.
10. Operation of shade should be performed only by authorized and qualified personnel, who have been trained in the safe and effective operation of the shade and
understand its safety features.
11. The safety features of the shade should never be disabled, bypassed, or overridden. The system should not be operated until all safety features are properly and
completely installed, calibrated, and tested.
12. Shade may need to comply with local, state, or district rules and regulations, in particular when installed in schools. All applicable rules and regulations should be
reviewed before installation and use.
13. Failure to precisely follow installation guidelines invalidates all warranties.
14. Custom products/installations may not be reflected in this manual. Call Draper, Inc., if you have questions regarding your installation.
PLEASE READ - Cleaning and Maintenance
Window covering products manufactured by Draper, when properly installed, should require no operational maintenance or lubrication.
However, exterior shading systems require additional cleaning and maintenance as needed.
Most standard Draper fabrics may be cleaned by vacuuming with a soft brush attachment. They also may be cleaned by using a sponge
or soft cloth and mild solution of warm soapy water. A mild dishwashing liquid is recommended. A clean dry cloth is recommended for
the metal finish.
Please refer to the document
Caring For Your Draper@Home Outdoor Window
Crank-Operated ZIP
3. Before mounting shades, verify
measurements on label provided with shade,
and ensure unit is installed at correct width.
4. All endcaps, fascia, pocket headbox, and
other hardware must be installed level.
Shades must be level and square.
ZIP can result in serious injury or death. Primarily, injuries can occur if the unit falls due to impre-
®
WARNING
Shades, available on the Draper website.
5. Read the following installation guidelines
thoroughly and follow them carefully.
Failure to do so may cause product to fall or
otherwise fail, and invalidates warranty.
6. Installer is responsible for selecting mounting
hardware appropriate for site conditions.
Important Safety Information
page 2 of 16
, Inc., is not
®