Draper FlexShade SkyLight 3 설치 지침 매뉴얼 - 페이지 2
{카테고리_이름} Draper FlexShade SkyLight 3에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Draper FlexShade SkyLight 3 6 페이지.
페이지 인쇄
SkyLight 3 Installation Instructions
Installing Mounting Brackets
Two (2) Roller Mounting Brackets are shipped assembled
and will need to be separated prior to installation.
(1) Remove two (2) screws from Lower Section of each
bracket using a Hex wrench.
(2) Separate Lower Sections of Mounting Brackets
and set aside (see Fig. 2).
(3) The two (2) Upper Sections of Mounting Bracket
will be mounted directly to the skylight window frame.
Caution: Before mounting shades, verify measure-
ments on the card provided with the shade, and
ensure the brackets are installed at the correct width.
(4) Hold Mounting Brackets in place along the length of
the window frame. Mark the location of the pre-drilled
mounting holes.
Please Note: Brackets must be installed level (see fig. 3) with center tab flush with
the window. This will allow adequate room for Motor End Trim to be installed later.
(5) Fasten Mounting Brackets to mounting surface using appropriate mounting
hardware (by others).
Brackets must
B
b
be installed level,
with Center Tab
w
flush with window
f
Mounting
Bracket
W IN D O W
F R A M E
L E N G T H
Installing Side Channels
(1) Hold the Side Channels in place and mark the location of the pre-drilled
mounting holes along the entire length.
N E L
S ID E C H A N
Mounting
Hardware
(by others)
(2) Drill pilot holes (if necessary).
(3) Secure the Side Channels with appropriate mounting hardware (by others).
The four pre-drilled holes at the end of the track will be used in the next step.
(4) Repeat steps (1) - (3) for the opposite side.
Upper
Section
Figure (2)
Wire Routing
(no fasteners)
Figure (3)
W I N D
O W
F R A M
E
W I D T
H
Mounting Hardware
(by others)
Figure (4)
Roller Assembly
Roller Assembly
Mounting Bracket
Mounting Bracket
(Upper Section)
(Upper Section)
W I N D
W IN D O W
O W
F R A M
F R A M E
E
W I D T
L E N G T H
H
www.draperinc.com
Installing End Pulley Brackets
Part One: Insert Relieving Roller Anchor
Before inserting the Relieving Roller Anchor, confirm measurements on the
card provided with the shade. The length of the shade will determine whether a
Relieving Roller is required and the Relieving Roller Anchor orientation.
Shade shorter than 122"
Relieving
Roller
Anchor
Lower
Section
Orientation:
(1) Insert the Relieving Roller Anchor into the Side Channel (see fig. 5) and slide
to the center of Side Channel. Repeat on the opposite side.
Part Two: Attaching End Pulley Brackets
R O L L
E R
T R A C
K
s li d e t o
C e n t e r
o f t r a c
W I N D O
W F R
(2) Align the End Pulley Brackets with the four (4) pre-drilled holes in the end of the
Side Channel. Attach using appropriate mounting hardware (by others).
Cable Exit /// Motor Trim Installation
(1) The center hole on the Motor Mounting Bracket is provided for Cable Exit.
Determine on which end of the Roller Assembly the Motor Cable is located.
Using a 5/16" Ø bit, drill through the mounting surface to provide an path for
the Motor Cable to exit the skylight frame (see Fig. 6).
(2) Next, attach the Motor Trim Extrusion using appropriate hardware (by others).
Attach Motor Trim
to the Top of Motor
Mounting Bracket
Figure (6)
(765) 987-7999
Shade longer than 122"
Relieving
End Pulley Bracket
Roller Anchor
Mounting
Hardware
(by others)
k
ID T H
F R A M E W
A M E L
W IN D O W
E N G T H
W IN D O W
F R A M E
L E N G T H
2
6
of
Figure (5)
Drill
5
/
" Ø Hole Through
16
Mounting Surface for
Motor Cable Exit
(one side only)