Draper Futureguard FlexShade Zip 설치 지침 매뉴얼 - 페이지 2
{카테고리_이름} Draper Futureguard FlexShade Zip에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Draper Futureguard FlexShade Zip 7 페이지.
페이지 인쇄
Futureguard® FlexShade Zip™
DIMENSIONS — HEADBOX STYLES
3
/
"
5
(92mm)
8
3
/
"
5
8
(92mm)
FlexShade Zip 92
Square Headbox
HARDWARE DIMENSIONS
1
/
"
5
8
(41mm)
1
/
5
(41mm)
/
"
3
8
(10mm)
¾"
(18mm)
Side Channel Dimensions
CABLE EXIT
The FlexShade Zip can be ordered with a cable exit pre-drilled in the top or back of the Headbox. If there is no
cable exit provided, you must drill one. Before drilling out a cable exit, remove the Roller Assembly from the
Headbox. (See Removing Roller Assembly section on Page 3)
Remove the 3 screws and the End Cap on the motor side of the Headbox and drill a
the 3 suggested locations (See Fig. 2). After drilling, replace the End Cap and return the Roller Assembly.
FlexShade Zip 92
½"
1
/
"
3
8
TOP
ATTACHING ANTI-INSECT BRUSH SEALS
The FlexShade Zip has optional Anti-Insect Brush Seals pre-installed along the width of the Headbox Fascia Cover.
There are also brush seals supplied for each of the Side Channels that will need to be inserted before installing the Side
Channels. After the screen is installed and before the Headbox Fascia Cover is installed, remove the double-sided tape
and apply the small brush seals to the face of the Side Channels as shown in (Fig. 3).
by Draper
5"
(127mm)
(127mm)
FlexShade Zip 127
Square Headbox
2"
(50mm)
"
8
1"
(26mm)
Hembar Dimensions
/
"
9
16
/
"
9
16
1¾"
SIDE
5"
(127mm)
5"
(127mm)
FlexShade Zip 127
Angled Headbox
4"
(102mm)
4"
(102mm)
3
/
"
5
8
(92mm)
3
/
"
5
8
(92mm)
1½"
1½"
½"
(38mm)
(38mm)
(19mm)
1½"
1½"
(38mm)
(38mm)
½"
(19mm)
Zip 92 Mounting Bracket
⁄
5
16
FlexShade Zip 127
½"
BACK
(OPTIONAL)
5"
(127mm)
5"
FlexShade Zip 127
Curved Headbox
1"
(25mm)
1¾"
1"
(45mm)
(25mm)
5"
(127mm)
1¾"
/
"
7
(22mm)
8
(45mm)
5"
(127mm)
½"
/
"
7
(19mm)
(22mm)
8
½"
(19mm)
" diameter hole in one of
½"
1
/
"
3
8
TOP
SIDE
page 2
3
/
"
5
(92mm)
8
3
/
"
5
8
(92mm)
FlexShade Zip 92
Curved Headbox
4"
(102mm)
1"
(25mm)
4"
(102mm)
1¾"
1"
(45mm)
(25mm)
1¾"
(45mm)
2¼"
(57mm)
2¼"
1½"
1½"
(57mm)
½"
(38mm)
(38mm)
½"
(19mm)
(19mm)
1½"
1½"
Zip 127 Mounting Bracket
(38mm)
(38mm)
½"
½"
(19mm)
(19mm)
Remove Three
Screws from
Endcap
Cable Exit Hole Ø:
Figure
5/16" (8mm)
Figure 2
½"
/
"
25
32
¾"
1¾"
BACK
Insect Barrier
Brush Seal
Figure
Figure 3