Bosch 800 Series 설치 매뉴얼 - 페이지 17

{카테고리_이름} Bosch 800 Series에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch 800 Series 48 페이지. Built-in wall ovens
Bosch 800 Series에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (24 페이지), 설치 매뉴얼 (40 페이지), 사용 및 관리 매뉴얼 (12 페이지), 설치 매뉴얼 (23 페이지), 설치 매뉴얼 (28 페이지), 설치 매뉴얼 (32 페이지), 사용 설명서 (32 페이지), 설치 매뉴얼 (32 페이지), 빠른 시작 및 안전 매뉴얼 (7 페이지), 사용 및 관리 매뉴얼 (40 페이지), 설치 매뉴얼 (40 페이지), 설치 매뉴얼 (32 페이지), 설치 지침 매뉴얼 (40 페이지), 사용 및 관리 매뉴얼 (33 페이지), 사용 및 관리 매뉴얼 (49 페이지), 빠른 시작 매뉴얼 (7 페이지), 빠른 시작 및 안전 매뉴얼 (13 페이지), 설치 매뉴얼 (32 페이지), 서비스 매뉴얼 (36 페이지), 설치 지침 매뉴얼 (29 페이지), 사용 및 관리 매뉴얼 (24 페이지), 사용 및 관리 매뉴얼 (40 페이지), 설치 지침 매뉴얼 (28 페이지)

페이지 인쇄

Checking Burner Cap Placement

Check to make sure that there is no gap between the

burner cap and burner base. See illustration below for

correct and incorrect placements of the burner cap.

You may gently try to move the burner cap from side to

side to check if it is properly placed. If properly placed,

the cap will click from side to side as the prongs hit the

groove ridge.

Install Grates

First position the outer grates, followed by the the central

grate. If you only have two grates, the order in which you

position them is not relevant.

Check the Installation

Place each correct-sized burner cap in its seated,

notched position and check the operation of the electric

igniters. Check the flame characteristics. The flame

should be blue with a minimal yellow tip on the outer

cone of the flames.

Checking the flame characteristics

Yellow flames:

Further adjustment is

required.

Yellow tips on outer

cones:

Normal for propane gas

Soft blue flames:

Normal for natural gas

Orange flames:

Can be normal if certain

types of humidifiers are

used in the home. Flames

should return to blue with-

out the humidifier running.

Note: If the flame is completely or mostly yellow, verify

that the regulator is set for the correct fuel. Retest after

adjustment.

Some yellow streaking is normal during the initial start-

up. Allow the appliance to operate for 4–5 minutes and

reevaluate before making adjustments.

Test for Gas Leaks

WARNING

RISK OF FIRE

Never check for gas leaks with a flame.

Leak testing is to be conducted by the installer according

to the instructions given in this section.

Turn on gas.

Apply a non-corrosive leak detection fluid. Include all

joints and fittings between the shutoff valve and the

appliance. Include gas fittings and joints in the

appliance if connections may have been disturbed

during installation.

Inspect for leaks. Bubbles appearing around fittings

and connections indicate a leak.

If a leak appears, turn off supply line gas shutoff valve

and tighten connections.

Retest for leaks. Turn gas back on at supply line

shutoff valve and reapply leak detection fluid.

When no bubbles appear, test is complete. Wipe off all

detection fluid residue.