Bosch 800 Series 설치 매뉴얼 - 페이지 16

{카테고리_이름} Bosch 800 Series에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch 800 Series 48 페이지. Built-in wall ovens
Bosch 800 Series에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (24 페이지), 설치 매뉴얼 (40 페이지), 사용 및 관리 매뉴얼 (12 페이지), 설치 매뉴얼 (23 페이지), 설치 매뉴얼 (28 페이지), 설치 매뉴얼 (32 페이지), 사용 설명서 (32 페이지), 설치 매뉴얼 (32 페이지), 빠른 시작 및 안전 매뉴얼 (7 페이지), 사용 및 관리 매뉴얼 (40 페이지), 설치 매뉴얼 (40 페이지), 설치 매뉴얼 (32 페이지), 설치 지침 매뉴얼 (40 페이지), 사용 및 관리 매뉴얼 (33 페이지), 사용 및 관리 매뉴얼 (49 페이지), 빠른 시작 매뉴얼 (7 페이지), 빠른 시작 및 안전 매뉴얼 (13 페이지), 설치 매뉴얼 (32 페이지), 서비스 매뉴얼 (36 페이지), 설치 지침 매뉴얼 (29 페이지), 사용 및 관리 매뉴얼 (24 페이지), 사용 및 관리 매뉴얼 (40 페이지), 설치 지침 매뉴얼 (28 페이지)

페이지 인쇄
Bosch 800 Series 설치 매뉴얼
WARNING
9
The rear vent trim has 3/16" (5 mm) standoffs to
keep the appliance slightly off of the back wall.
Do not remove or tamper with standoffs due to
potential temperature issues.
Check for proper installation and use of the anti-tip
10.
bracket. Carefully tip the range forward pulling from
the back to ensure that the anti-tip bracket engages
the range leg and prevents tip-over. The range should
not move more than 1" (2.5cm).

Connect Electrical Supply

WARNING
9
Before you plug in an electrical cord or turn on
power supply, make sure all controls are in the OFF
position.
Before connecting the 5 ft (1.5 m) supply cord to a wall
receptacle, make sure that the gas shut-off valve and all
burner controls are in the OFF position.
WARNING
9
ELECTRICAL GROUNDING INSTRUCTIONS
This appliance is equipped with a three-prong
grounding plug to protect you against the risk of
shocks and it should be plugged directly into a
properly grounded receptacle. Do not cut or remove
the grounding prong from this plug.

Burner Cap Placement

Sealed burners
Your new cooktop has sealed gas burners. There are no
burner parts under the cooktop to clean, disassemble or
adjust. Your cooktop has three different burner sizes:
small, large and dual-flame.
WARNING
9
To prevent flare-ups, do not use the cooktop without
all burner caps and all burner grates properly
positioned.
WARNING
9
To prevent burns, do not touch burner caps
orgrates while hot. Turn the cooktop off and allow
the burners to cool.
16
The burner parts must be correctly positioned for the
cooktop to function properly. If the burner parts are not
correctly positioned, one or more of the following
problems may occur:
Burner flames are too high.
▯
Flames shoot out of burners.
▯
Burners do not ignite.
▯
Burner flames light unevenly.
▯
Burner emits gas odor.
▯
Burner Cap and Burner Base Placement
After electrical connection is complete, place each
burner base on the corresponding location on the
cooktop. One of the three bars on the burner base
should line up with the notch and prevent the base from
rotating. The small hole or cutout near the edge should
also line up with the igniter. Pay special attention to avoid
damaging the igniter during installation of the base. See
Illustration below.
Once each base is located and resting evenly, place
each burner cap on its correct burner base. See
Illustration.
Place burner cap gently on top of base so that the
prongs of the burner base fit snugly into the groove of
the burner cap.
If the maintop is removed by a certified installer (for
example to check electrical or piping connection) the
panhead screws that were removed must be re-installed
to ensure proper functionality of burners.