Alemlube 6336N 소유자 기술 매뉴얼 - 페이지 6
{카테고리_이름} Alemlube 6336N에 대한 소유자 기술 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Alemlube 6336N 6 페이지. 2.5kg grease kit
페이지 인쇄
PROBLEM
The hand piece fails to deliver grease when on
the high volume setting
Control push rod in the control body leaks
Hand piece leaks at the grease swivel
When on the high volume setting, the hand
piece is too slow and too hard to operate
GENERAL INSTRUCTIONS
ALWAYS When the gun has been serviced and the trouble found to be caused by dirt in the valves, the pump unit should also be
cleaned out thoroughly to eliminate the dirt at its source.
CLEANLINESS Dirt and foreign matter (lint, etc.) can seriously affect operation and machinery. Dismantling and reassembly of
this unit should only be attempted in clean conditions.
NSW/ACT
QLD/PNG
TEL: (02) 9677 1555
TEL: (07) 3204 9166
FAX: (02) 9675 1155
FAX: (07) 3204 1224
Visit our website at
C
A
U
S
E
(a) There is dirt on the valve inlet seat (24).
(b) Operating plunger control (25) sticking in
control body assembly (26).
O'Ring (31) is worn
Worn seals (1
) 1
&
(
2 1
)
(a) Spring (16) may have weakened or collapsed
and are blocking the flow of grease
(b) The grade of grease being used is too heavy.
(c) Too much comprehension on the outlet
spring (2).
VIC/TAS
WA
TEL: (03) 8787 8288
TEL: (08) 9302 4199
FAX: (03) 8787 8266
FAX: (08) 9303 2095
www.alemlube.com.au
(a) IMPORTANT: This problem will result in
a decreased volume of grease being dispensed
per shot.
Remove control body (26) and tap out valve
inlet seat (24), O' Ring (31), ball (30) and
spring (27). Clean the ball and seat and
replace in the following order – spring, ball,
O'Ring, valve seal and control body.
(b) Replace the control body assembly (26).
Remove control body assembly (26) from the
hand piece. Also remove the operating control
plunger (25) from the control body and replace
with spare part kit number 6336N-SPK7
U
n
c s
e r
w
b
l l a
seals out and use spare part kit number
6336N-SPK8. Be careful to replace the
components in the following order – O'Ring
(13) and washer (12). Locate O'Ring (11) on
to the hand piece casting (8). Reassemble ball
socket retainer on to the hand piece.
(a) Replace spring (16) and use spare part kit
number 6336N-SPK5 and valve stem spare part
kit number 6336N-SPK1.
(b) Change to an NLGI2 or lower viscosity
grease.
(c) Reset the spring keeper screw as noted in
the 2.5kg grease kits coupler leaks section. If
the problem persists, you will need to replace
the outlet body assembly.
SA/NT
TEL: (08) 8241 7111
FAX: (08) 8241 7011
Email - [email protected]
S
O
L
U
T
I
O
N
o s
k c
t e
e r
i a t
e n
( r
5 1
, )
u p
h s
the
NZ
TEL: (09) 447 1007
FAX: (09) 447 1008
6