Bosch FAP-OC 500Series 사용 및 관리 설명서/설치 지침 - 페이지 28

{카테고리_이름} Bosch FAP-OC 500Series에 대한 사용 및 관리 설명서/설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch FAP-OC 500Series 40 페이지. Built-in wall ovens
Bosch FAP-OC 500Series에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (21 페이지), 사용 설명서 지침 (40 페이지), 설치 매뉴얼 (6 페이지), 제품 정보 (40 페이지), 설치 매뉴얼 (28 페이지), 사용자 설명서 (48 페이지), 사용자 설명서 (48 페이지), 설치 매뉴얼 (28 페이지), 사용 및 관리 매뉴얼 (44 페이지), 설치 매뉴얼 (32 페이지), 빠른 참조 매뉴얼 (4 페이지), 사용 및 관리 매뉴얼 (27 페이지), 설치 매뉴얼 (24 페이지), 설치 매뉴얼 (32 페이지), 사용 및 관리 매뉴얼 (24 페이지), 설치 매뉴얼 (28 페이지), 서비스 매뉴얼 (41 페이지), 사용 및 관리 매뉴얼 (21 페이지), 설치 매뉴얼 (32 페이지), 서비스 매뉴얼 (36 페이지), 설치 매뉴얼 (32 페이지), 빠른 시작 및 안전 매뉴얼 (13 페이지)

페이지 인쇄

Bosch FAP-OC 500Series 사용 및 관리 설명서/설치 지침

Default Program and Option settings

At the factory, temperature and spin speed options, and

cycle duration ("Finish in" time) are pre-set for all cycles.

After selection of the cycle, these values are displayed in

the display field.

You can change the default settings as follows.

Changing the temperature range

Before and during the cycle, you can change the default

temperature range depending on the cycle progress.

Press the appropriate button until the desired setting is

displayed.

The maximum temperature range that can be set

depends on the cycle selected.

Changing the spin speed range

Before and during the cycle, you can change the spin

speed range depending on the cycle progress.

Touch the appropriate button until the desired setting is

displayed.

Additional Program Option settings

Extra Rinse

+1, +2

This feature is helpful for locations with very soft water or

to generally improve rinsing results. It allows up to 2

additional rinse cycles to be added to selected programs

and will increase program time.

Prewash

For heavily soiled washing. Pour 1/3 of normal detergent

amount into pre-wash chamber I and remaining 2/3 into

main wash chamber II.

SpeedPerfect

For washing in a shorter time with a washing result

comparable to that of the standard program.

Note: Do not exceed the maximum load. ~ Program

selection table; Page 26

No Spin: This option eliminates the final spin and the

load remains saturated with the final rinse water. The

pump is activated to remove all residual water.

~ Program selection table; Page 26

Finish in

The program end (Finished in) time can be set in one

hour increments to a maximum of 24 h (hours). After

selecting the desired washing program (at the dial) but

before touching the Start button, touch the Finish in

button until the desired time is displayed, e.g. 8 h, then

touch the Start button to start the washer.

NOTICE: The cycle duration is included in the set Finish

in time.

Here is an example of a 2hr:30min cycle time and an 8 h

Finish in time.

8 h is displayed (until the Energy-Saving mode activates)

and counts down (approximately 5hr:30min) until the

washing cycle begins (at 2hr:30min) then the cycle

duration 2:30 is displayed and began. Total time

approximately 8 hours.