Anchor AL-WB 소유자 매뉴얼 - 페이지 3

{카테고리_이름} Anchor AL-WB에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Anchor AL-WB 4 페이지. Uhf tour guide system
Anchor AL-WB에 대해서도 마찬가지입니다: 사양 (1 페이지)

페이지 인쇄

ASSISTIVE LISTENING SYSTEM OPERATION

DIVERSITY WIRELESS BY ANCHOR AUDIO

Anchor Audio Assistive Listening Systems are 16 channel UHF diversity wireless systems. Diversity wireless technology

utilizes two independent antennae to receive signals. The diversity feature means the receiver will process the stronger

of the two antenna signals, effectively minimizing dropouts and interference from other sources.

CHANNEL SELECTION

Before you can use your wireless system, you will need to select a wireless frequency and set the receivers and trans-

mitters you are using to that channel.

1. Choose from any of the available wireless channels: 1 thru 16

2. Set each receiver and transmitter to the channel you have chosen

NOTE: To operate the transmitter & receiver must be set to the same channel.

QUICK SYSTEM SETUP INSTRUCTIONS

TOUR GUIDE SYSTEM/TOUR-60

1. Select a wireless channel

2. Set transmitter channel (page 4)

3. Set receivers to same channel (page 3)

4. Adjust volume on receivers to desired level (page 3)

4-USER DELUXE SYSTEM/ALD-40

1. Select a wireless channel

2. Set transmitter channel (page 5)

3. Set receivers to same channel (page 3)

4. Setup UHF-6400 wireless microphone

(UHF-6400 User Manual)

5. Connect input source to transmitter -

microphone, stereo system, etc. (page 5)

6. Set output levels on transmitter (page 5)

7. Adjust volume on receivers to desired level (page 3)

4-USER BASIC SYSTEM/ALB-40

1. Select a wireless channel

2. Set transmitter channel (page 5)

3. Set receivers to same channel (page 3)

4. Connect input source to transmitter - microphone,

stereo system, etc. (page 5)

5. Set output levels on transmitter (page 5)

6. Adjust volume on receivers to desired level (page 3)

BELT PACK RECEIVER SETUP

Model: AL-WB

Belt pack receiver for use with Anchor Audio 16 channel base station transmitter, handheld microphone or belt pack

transmitter. The receiver operates in the UHF band frequency and is powered by two DC 1.5V "AA" size batteries.

BELT PACK SETUP

1. INSERT BATTERIES: Open battery compartment by sliding latch down and insert two "AA" batteries.

2. SET CHANNEL: Using the included screwdriver turn the Channel Selection Dial to the same channel as the

transmitter, close compartment door.

NOTE: Transmitter & receiver MUST be set to the same channel to operate.

3. CONNECT HEADPHONES: Insert the stereo headphone plug into the Stereo Earphone Jack.

NOTE: For stereo audio output equipment, insert plug into the Stereo Recording Jack.

4. POWER ON: Slide the Power Switch to the "ON" position to power up the receiver.

5. VOLUME LEVEL: Adjust the volume to a comfortable listening level by turning the Volume Control knob.

BODY PACK RECEIVER

Model: AL-WB

CHARGING

INPUT JACK

(ON SIDE)

CHANNEL

SELECTION DIAL

BATTERY

COMPARTMENT

BELT PACK RECEIVER POWER LED

Power On:

Flash red once and fade

Green Light On:

Receiver is getting signal

VOLUME CONTROL

POWER LED

POWER SWITCH

STEREO

RECORDING

JACK

STEREO

EARPHONE

JACK

BATTERY

COMPARTMENT

LATCH

Red Light On:

Batteries need charging

Red Light Flashing: Batteries are charging