Electrolux Energy Star WT30H208DU 사용 설명서 - 페이지 16
{카테고리_이름} Electrolux Energy Star WT30H208DU에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Electrolux Energy Star WT30H208DU 18 페이지. Electrolux dishwasher instruction manual
Electrolux Energy Star WT30H208DU에 대해서도 마찬가지입니다: 사양 시트 (2 페이지)
페이지 인쇄
cedure described in the paragraph "Manual activa-
tion" at least 3 times.
•
Completely drain the boiler by simultaneously pres-
sing the buttons as shown in the figure.
A buzzer indicates completion of drainage.
•
Spread a thin film of petroleum jelly over all the stain-
less steel surfaces.
Preventive maintenance
The preventive maintenance message "CALL" may be
activated.
Upon reaching the set number of cycles (e.g. 20000),
appears on the display.
This message advises calling a qualified authorized ser-
vice technician for a general check-up on of the state of
the appliance.
NOTICE: CONTACT YOUR AUTHORIZED SERVICE
COMPANY
TO
PERFORM
REPAIRS
NOTICE: Using any parts other than genuine factory
manufactured parts relieves the manufacturer of all war-
ranty and liability.
NOTICE: Manufacturer reserves the right to change spe-
cifications at any time without notice.
WARNING: The equipment warranty is not valid unless
the appliance is installed, started and demonstrated
under the supervision of factory trained installer.
WARNING: The unit must be installed by Personnel who
are qualified to work with electricity and plumbing.
Improper installation can cause injury to personnel
and/or damage to the equipment. The unit must be
installed in accordance with applicable codes.
D6
UNDERCOUNTER DISHWASHER WITH
INCORPORATED CONTINUOUS WATER
SOFTENER
These models have a continuous softener in the
dishwasher water circuit. By means of special resins,
this device removes the calcareous substances from the
feed water, supplying decalcified water for washing.
For the continuous softener to work properly the resins
must be regenerated periodically, with frequency depen-
ding on the hardness of the water and the number of
wash cycles carried out.
Unlike conventional water softeners, this continuous sof-
tener does not require machine stops for regenerating
the resins.
18
1
2
3
MAINTENACE
AND
AUTONOMY OF A COLUMN OF RESINS ACCORDING
TO THE CHANGE IN INLET WATER HARDNESS
ppm
150
200
250
300
350
400
The factory setting of max. outlet water hardness is 100 ppm / 10 °fH.
Salt container
The water can only be softened if there is salt in the spe-
cial container. The salt container must be filled when the
dishwasher is used for the first time and whenever the
SAL 0
message
is displayed at the start of a wash
cycle.
No salt in the container
SAL 0
If the message
wash cycle, it means that the salt container is empty.
Wash cycles can be started just the same, even if the
display signals no salt; in which case the water used for
washing is not softened.
IMPORTANT:
!
Open the salt container only when the
SAL 0
message
the cap when the message
displayed can cause spilling of the saline
solution and compromise correct machine
operation.
How to fill the salt container
•
Switch off the dishwasher by pressing button "A"
(Figure 14).
•
Unscrew cap "A" (Figure 20) of the salt container, tur-
ning it anticlockwise.
A
Figure 20
°fH
Number of Cycles
15
14
20
10
25
7
30
6
35
5
40
4
is displayed at the start of a
is displayed. Opening
SAL 0
is not