Andersen VeriLock 매뉴얼 - 페이지 4
{카테고리_이름} Andersen VeriLock에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Andersen VeriLock 6 페이지. Security sensor lock
Andersen VeriLock에 대해서도 마찬가지입니다: 매뉴얼 (13 페이지), 매뉴얼 (6 페이지), 애플리케이션 (10 페이지), 애플리케이션 (6 페이지), 매뉴얼 (6 페이지), 매뉴얼 (5 페이지), 서비스 매뉴얼 (6 페이지)
페이지 인쇄4
Sensor contains an anti-tamper switch. Do not apply sensor over wet
finish or rough/dirty surface. Improper switch function may result.
Interior
El sensor contiene un interruptor de seguridad. No instale el sensor en
acabados húmedos o superficies sucias/ásperas. Esto podría dar como
resultado un mal funcionamiento del interruptor.
VeriLock Sensor
(anti-tamper switch)
Sensor VeriLock
(interruptor de
seguridad)
(back view)
(vista trasera)
Verify panel surface is clean and dry. Position latch lever and VeriLock sensor assembly on panel as shown and fasten using #10 x 2" screws
included. The indicator light will illuminate for one (1) second when the sensor assembly is applied to the panel as the anti-tamper switch is
depressed.
Verify panel surface is clean and dry. Position latch lever and VeriLock sensor assembly on panel as shown and fasten using #10 x 2" screws
included. The indicator light will illuminate for one (1) second when the sensor assembly is applied to the panel as the anti-tamper switch is
depressed.
Magnets are small parts and, if swallowed, could pose a choking hazard to young children.
Los imanes son partes pequeñas que, en caso de ingesta, pueden representar un riesgo de asfixia para niños pequeños.
5
Do not pinch or drill through weatherstrip. Product
damage will occur.
Interior
Do not pinch or drill through weatherstrip. Product
damage will occur.
Position magnet on side jamb behind weatherstrip. Slide tight to interior edge of lock receiver as shown and pre-drill two (2) 1/8" holes, 3/4"
deep using magnet holes as a template. Fasten with two (2) #6 x 1" screws.
Position magnet on side jamb behind weatherstrip. Slide tight to interior edge of lock receiver as shown and pre-drill two (2) 1/8" holes, 3/4"
deep using magnet holes as a template. Fasten with two (2) #6 x 1" screws.
9136270
(front view)
(vista frontal)
Magnet Application/
Magnet /
Imán
Side Jamb
Interior Side
Jamba lateral
Lado interior
Weatherstrip
Lock Receiver
Burlete
Receptor del cerrojo
Indicator
Light
Luz
indicadora
Aplicación del imán
Side jamb and weatherstrip shown transparent for clarity.
La jamba lateral y el burlete se muestran transparentes para
que haya claridad.
1/8" Drill Bit
Broca para taladro
de 1/8"
4
Latch Lever
(unlocked position)
Palanca del pestillo
(en posición de
desbloqueo)
#10 x 2" Screws
(included)
#10 x 2" Screws
(included)
#6 x 1" Screw
Tornillo n.° 6 x 1"
Phillips Screwdriver
Destornillador Phillips