Atlantic LST 800W 설치 및 제어 매뉴얼 - 페이지 2

{카테고리_이름} Atlantic LST 800W에 대한 설치 및 제어 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Atlantic LST 800W 7 페이지. Low surface temperature convector panel heaters with electronic 7 day timer

페이지 인쇄

Overview

Please read this guide carefully and retain for future use and

maintenance.

This appliance has been designed and manufactured to the

highest international standards, however, care must be taken

for optimal results and safety. This appliance also meets

the requirements of EU Directive 2014/30/EU for EMC and

2014/35/EU Directive.

Safety & Care

Our Low Surface Temperature heaters have been designed and

built to the NHS requirement for safe surface temperatures

which is that no surface which can be touched by the user

will be more than 43 degrees C (at a room temperature of 21

degrees C.) This means that our Low Surface Temperature

heaters out-perform the European Standard by a significant

margin.

The appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental apabilities or

lack of experience and knowledge unless they have been given

supervision or instruction concerning use of the appliance

by a person responsible for their safety. Children should be

supervised to ensure that they do not play with the appliance.

Warning

• Do NOT site the appliance into a corner.

• Do NOT handle the appliance with wet hands.

• Do NOT use the appliance in workshops or rooms where

excessive dust is generated or present.

• Ensure that nothing is pushed into the air outlet of this

appliance.

• Do NOT touch outlet grille when the appliance is in use.

• Do NOT cover or restrict the appliance when in use.

• Do NOT use the appliance if damaged.

• Do NOT leave the appliance unattended where young

children are present.

Connection to the Main Supply

Electrical installation should be carried out by a competent

installer, preferably registered with NICEIC (National Inspection

Council for Electrical Installation Contracting) in accordance

with the 17 edition of the IEE Wiring Regulations, (BS.7671),

and any relevant Local Authority Bye-Laws. This heater is fitted

with a 3-core mains supply cable and should be permanently

connected to the electricity supply via a double pole switch

having 3mm gap on each pole.

A switched Fused Connection unit to BS.1363. Part 4 is a

recommended mains supply connection accessory to ensure

compliance with safety requirements applicable to fixed-wiring

installation.

Note: When switched on for the first time the appliance may

emit a slight smell. This is purely the evaporation of a fluid used

in the manufacturing process.

WARNING: This appliance must be earthed.

Thermally Operated Cut-Out

The appliance is fitted with a thermally operated cut-out (TOC).

This is a safety device, which switches the heater off if, for any

reason, the appliance overheats. The TOC can only be re-set

after the appliance has cooled down. In order to re-set the

TOC, proceed as follows:

• Switch off appliance and leave for approximately 10 minutes.

• Switch appliance back on and the TOC will re-set.

• Ensure that the appliance is functioning correctly. If the TOC

control operates again, the appliance should be checked by a

competent electrician.

The heater carries a 'Do Not Cover' label to warn the user that

if the appliance is covered, there is a risk of overheating.

Cleaning

Always disconnect the heater from the mains before cleaning.

The heater should not require any maintenance, but it is

strongly advised that it is kept clean. An occasional wipe over

with a soft cloth is all that should be necessary.

• Do NOT use metal or furniture polish on any part of the

heater.

• Do NOT touch the heater with wet hands or in any way bring

water into contact with it.

If the supply cord is damaged, it must be replaced by the

manufacturer or its service agent or a similarly qualified person

in order to avoid a hazard.

Mounting

To wall mount, the wall bracket supplied must be used. Remove

the wall bracket from the heater, with the chains attached, by

removing the 2 securing screws from the top of the rear panel.

Fix the wall bracket to the wall using 4 screws.

Fig 1: Present the heater to the bracket

Fig 2: Locate the heater onto the bottom lugs via the 2 slots in

rear panel. Hinge the heater upwards and reattach the chain

assembly, then move the heater to the upright position. The

link plates should slide under the slotted bracket lip.

Fig 3: Tighten both retaining screws.