Bosch 2 사용 설명서 - 페이지 8

{카테고리_이름} Bosch 2에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch 2 8 페이지. Mini blender
Bosch 2에 대해서도 마찬가지입니다: 빠른 설치 매뉴얼 (16 페이지), 설치 및 활용 매뉴얼 (18 페이지), 원본 사용 설명서 (13 페이지), 원본 사용 설명서 (22 페이지), 사용 설명서 (32 페이지), 사용자 설명서 (28 페이지), 사용자 설명서 및 설치 지침 (16 페이지), 사용 설명서 (42 페이지), 사용 설명서 (8 페이지), 사용 설명서 (12 페이지), 빠른 시작 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (9 페이지), 사용 설명서 및 설치 지침 (36 페이지), 사용자 설명서 및 설치 지침 (48 페이지), 사용 설명서 (26 페이지), 빠른 참조 매뉴얼 (2 페이지), 사용자 설명서 및 설치 지침 (24 페이지), 사용 설명서 (42 페이지), 사용 정보 (28 페이지), 사용자 설명서 (40 페이지), 사용자 설명서 및 설치 지침 (35 페이지), 사용자 설명서 (24 페이지)

페이지 인쇄
Bosch 2 사용 설명서
What to do if...
Water is leaking out.
– Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
No water supply.

– Start/Pause

Detergent not dispensed.
– Tap not turned on?
– Filter blocked? Clean the filter
– Supply hose kinked or trapped?
Washing machine door
– Safety function active. Programme stopped?
cannot be opened.
– - - - - (Rinse stop = no final spin) selected?
Programme does not start. – Start/Pause
– Washing machine door closed?
– Childproof lock active? Deactivating
Detergent solution is not
– - - - - (Rinse stop = no final spin) selected?
drained.
– Clean the detergent solution pump
– Clean the waste pipe and/or drainage hose.
Water not visible in the
– Not a fault - water below the visible area.
drum.
Spin result not satisfactory.
– Not a fault - the imbalance monitoring system has interrupted the spin
Laundry wet/too damp.
because the laundry is unevenly distributed.
Distribute large and small items of laundry evenly in the drum.
– Speed selected too low?
The programme duration
– Not a fault - the programme cycle is optimised for the particular
changes during the wash
washing process. This can cause changes in the programme duration
cycle.
on the display panel.
Spin cycle performed
– Not a fault - unbalanced-load detection system is adjusting the
several times.
imbalance.
Residual water in the
– Not a fault - the action of the care product is not affected.
compartment for care
– Clean the insert if necessary
products.
Odour formation in the
– Run programme
washing machine.
detergent.
Status display
flashing.
– Too much detergent used?
Appliance has detected a
Mix one tablespoonful of fabric softener with ½ litre water and pour
detergent overload.
into compartment II (Not for outdoor fabrics, sportswear fabrics or
those made with down.)
–
Reduce the detergent dosage for the next wash cycle
Loud noises, vibrations and
– Are the appliance feet fixed?
"wandering" during the
Secure appliance feet
spin cycle.
– Transportation safety devices removed?
Remove transportation safety devices
Display panel/indicator
– Power cut?
lamps do not function
– Circuit breakers tripped? Switch the circuit breakers back on or
during operation.
replace.
– If the fault occurs repeatedly, call the after-sales service.
Programme sequence
– Not a fault - unbalanced-load detection system is adjusting the
longer than usual.
imbalance by repeatedly redistributing the laundry.
– Not a fault - foam detection system active - adds an additional rinse
cycle.
There are detergent
– Occasionally, phosphate-free detergents contain water-insoluble
residues on the laundry.
residues.
– Select Rinse
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Turn the programme selector to Off and remove the mains plug from the socket.
– Turn off the water supply and call the after-sales service
not selected?
page 11.
page 4.
page 3,4.
or Ready in
time selected?
page 5.
page 3, 4.
page 11.
page 5.
page 10.
Cottons 90 °C without laundry. Use standard
.
Installation instructions.
Installation instructions.
or brush down the laundry after washing.
Installation instructions.
Washing machine
WAB20267IN
en operating instructions
11