DS Produkte 06723 사용 설명서 - 페이지 3

{카테고리_이름} DS Produkte 06723에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. DS Produkte 06723 6 페이지. Tunnel light

페이지 인쇄

■

Always replace all batteries together. Do not use batteries of

different types or brands, or batteries with different capacities.

When replacing batteries, ensure the correct polarity (+ / –).

■

Remove the batteries when they are dead or if you will not be

using the article for a prolonged period. This will prevent any

damage if a battery leaks.

■

If a battery has leaked, do not allow your skin, eyes and mucous

membranes to come into contact with the battery acid. If you

touch battery acid, rinse the affected area with abundant fresh

water immediately and contact a doctor as soon as possible.

■

Remove a dead battery immediately and clean the contacts

before you insert new batteries.

■

Use suitable fastening material to hang up the article (not sup-

plied with the article). If you are unsure which fastening ma-

terial is suitable for your wall, seek advice from a specialist

stockist.

■

Set up or attach the article in a safe place on a dry surface.

■

Before drilling, ensure that there are no pipes or cables behind

the intended drilling point.

■

Do not place any heavy objects on the article.

■

Do not place any containers ﬁ lled with liquid, for example vas-

es, on or directly next to the article.

■

Protect the article from heat sources, naked ﬂ ames, sub-zero

temperatures, persistent moisture, wet conditions and collisions.

■

The article must not be used if it shows obvious signs of dam-

age.

■

The individual LEDs cannot be replaced.

Items Supplied and Article Overview

NOTE: The article can be operated both with a 4.5-volt DC

mains adapter (4.5 volts, 500 mA) and with three 1.5-volt

batteries of the AA type. Batteries and mains adapters are

not supplied with the device!

Inserting / Changing Batteries

1. Open the battery compartment (5): Grip and press down the

locking lug on the battery compartment cover. Lift up the cover

at the same time.

2. Take the used batteries out if necessary and insert 3 x 1.5 V

batteries of the AA type. Pay attention to the correct polarity

(+ / –).

3. Reattach the battery compartment cover and press it shut.

Make sure that the locking lugs sit in the recesses which are

provided for them. You must hear and feel it engage.

Connecting the Mains Adapter

1. Before connecting the mains adapter, make sure that there are

no batteries in the battery compartment.

2. Connect a 4.5-volt DC mains adapter to the connecting socket

(3) on the article.

3. Connect the mains adapter to a properly installed socket that

is easily accessible. Make sure that the cable of the mains

adapter does not present a trip hazard.

DS Produkte GmbH, Am Heisterbusch 1, 19258 Gallin, Germany •

1 Mirror

2 On / Off switch

3 Connecting

socket for mains

adapter

4 Feet

5 Battery compart-

ment (on the

back)

Customer Service / Importer:

*) Calls subject to a charge. Costs vary depending on the provider.

Putting Into Operation

1. Unpack – Unpack all parts and check the items supplied for

completeness (see the "Items Supplied and Article Overview"

section) and possible transport damage. If you ﬁ nd any dam-

age to the components, do not use them (!), but contact our

customer service department.

2. Attach or set up – Attach the article at the height you want on

a wall using suitable fastening materials if necessary.

It is essential that you follow the safety instructions for as-

sembly (see the "NOTE – Risk of Damage to Material and

Property" section).

The article can also be set up on a ﬂ at,

dry surface using the feet (4). To do this,

insert the feet into the recesses on the

back of the article.

3. Power supply – Connect the mains adapter to the article or

insert batteries into the battery compartment (see previous

sections).

4. Switch on / off – To switch on the article, move the On / Off

switch (2) to position •.

To switch the article off again, move the On / Off switch (2) to

the position without a dot.

Cleaning and Storage

CAUTION!

■

Under no circumstances should you use any corrosive or abra-

sive cleaning agents or sponges to clean the article. These

can damage the surface.

1. Remove the batteries from the article (see the "Inserting /

Changing Batteries" section).

2. Clean the article with a soft cloth and a little mild detergent

if necessary. Then dry it thoroughly before it is repositioned

and / or stored away again.

3. Store the article in a dry place that is protected from sunlight

and is not accessible to children and animals.

Technical Data

Model number:

Article number:

Power supply:

Disposal

Dispose of the packaging in an environmentally friendly

manner and take it to a recycling centre.

Dispose of the article in an environmentally friendly man-

ner at a recycling centre for used electrical and electronic

devices. It should not be disposed of in the normal house-

hold waste. More information is available from your local

authorities.

The batteries should be removed prior to disposal of the

article and disposed of separately. To protect the environ-

ment, non-rechargeable and rechargeable batteries must

not be disposed of with normal household waste, but must

be taken to suitable collection points. Also note the relevant

statutory regulations governing the disposal of batteries.

✆

+49 38851 314650 *)

Instructions

The feet can be stored on the

back of the article.

I2187

06723

4.5 V

(3 x 1.5 V batteries, AA type)

Z 06723 M DS V1 0817