DSC WT5500 설치 지침 매뉴얼 - 페이지 2

{카테고리_이름} DSC WT5500에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. DSC WT5500 8 페이지. Wireless panel & keypad
DSC WT5500에 대해서도 마찬가지입니다: 빠른 시작 설치 매뉴얼 (2 페이지)

페이지 인쇄

English

Installation Instructions

The WT5500 keypad can be used on security systems with up to 64

zones. The WT5500 keypad is compatible with the SI9155 system.

Specifications

• Temperature range: -6°C to +54°C (22°F to 140°F), Temperature

range for UL/ULC: 0°C to +49°C (32°F to 120°F)

• Humidity (MAX): 93%R.H.

• Plastic enclosure protection degree: IP30, IK04

• Transformer voltage: 4.5V @ 0.5A

• Battery: 3V

• WT5500 Current draw: 50mA (standby)/125mA (maximum)

• Wall mount tamper

• 5 programmable function keys

• Ready (Green LED), Armed (Red LED), Trouble (Yellow LED), AC (Green

LED)

• Frequency: 433.92MHz (WT5500-433 only)

• Frequency: 868.35MHz (WT5500-868 only)

Unpacking

The WT5500 keypad package is available in five distinct configurations,

Standard, Proximity, Complete, Desk Stand, and Proximity Tags Only. The

contents of each are described below.

WT5500 - STANDARD

WT5500P - PROXIMITY

•1 WT5500 keypad

•1 WT5500P keypad

•1 WT5500BRK wall bracket

•1 Installation manual

•1 Inner door sticker

•4 AA batteries

•1 Hardware pack

•1 PT4 (433MHz proximity tag) or

PT8 (868MHz proximity tag)

WT5500D - COMPLETE

WT5500DMK - DESK STAND

•1 WT5500 keypad

•1 WT5500DMK keypad

•1 WT5500X AC transformer

•1 WT5500DMK desk stand

•1 Installation manual

•1 WT5500BRK wall bracket

•1 Hardware pack

•1 Installation manual

•1 Inner door sticker

•4 AA batteries

•1 Hardware pack

PROXIMITY TAGS ONLY

•1 PT4 (433MHz proximity tag) or

PT8 (868MHz proximity tag)

•1 Installation manual

Mounting

You should mount the keypad where it is accessible from designated points

of entry and exit. Once you have selected a dry and secure location, perform

the following steps to mount the keypad.

Mounting Plate

1. Locate the screw holes (4) at each corner of the mounting plate.

Screw

Holes

Mounting

Tabs

Screw

Holes

9049

2. With the smooth face of the mounting plate facing up, use the four screws

provided to affix the mounting plate to the wall.

3. Align the four mounting slots in the WT5500 housing with the four

mounting tabs protruding from the mounting plate.

4. Slide the unit into place.

5. Firmly but carefully snap the unit down onto the mounting plate.

Desk Stand

1. Place the desk stand on a secure, uncluttered surface.

2. Align the four mounting slots in the WT5500 housing with the four

mounting tabs protruding from the desk stand.

3. Slide the unit into place.

4. Firmly but carefully snap the unit down onto the desk stand.

Apply Battery Power

1. Slide the unit up and out from the mounting plate. The bay for the four AA

batteries is open and clearly visible at the back of the unit.

Tamper

Switch

Batteries

Screw

Holes

9048

2. Insert the batteries as directed on the unit.

3. Replace the unit on the mounting plate.

Apply AC Power

1. Slide the unit up and out from the mounting plate.

Screw

2. Locate the AC adaptor jack at the back of the unit housing.

Holes

3. Place the AC adaptor plug in the housing indentation, perpendicular to the

unit. Insert the adaptor plug firmly into the jack.

4. Pivot the adaptor plug downwards so that it fits flush with the housing.

Guide the AC wire along the channel provided in the unit housing; the wire

should finally extend through the bottom of the housing.

5. Replace the unit on the mounting plate.

6. Plug the AC adaptor into a wall outlet.

Programming the Keypad

There are several programming options available for the keypad. These are

described below. Programming the keypad is similar to programming the

rest of the system. To turn an option on or off, press the number correspond-

ing to the option on the number pad. The numbers of the options that are

currently turned on will be displayed along the top of the LCD. For informa-

tion on programming the rest of your security system, please refer to your

system's Installation Manual.

Broadcasting LCD Labels

All LCD programming is done using the keypad. If more than one LCD key-

pad is present on the system, labels programmed at one keypad can be

broadcast to all other LCD keypads. Perform the following procedure in order

to broadcast labels:

1. Program one LCD keypad completely.

Mounting

Holes

Plug

Wire

Channel

Mounting

Holes