DSC 3g4000 설치 매뉴얼 - 페이지 4

{카테고리_이름} DSC 3g4000에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. DSC 3g4000 8 페이지. 3g (hspa) wireless alarm communicator

페이지 인쇄

Ratings

Power Supply Ratings

Input Voltage (Nominal):. . . . . . . . . . . 9-14V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.8V

Input Current: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500mA (9-14Vdc) or 700mA (13.8V

Current Consumption

Average: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40mA*

Peak (no battery): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180mA*

Peak (with battery): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350mA*

* Plus any current drawn from the 3G4000 + terminal

Battery: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NiMH, rated 7.2V, 2.2Ah

Battery charging voltage (maximum): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9.1V

Battery charging current: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60mA

NOTE: Battery must be replaced every 3-5 years.

Operating frequency: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 850/1900MHz

Antenna gain: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0dBi

Environmental Specifications

Operating temperature: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C-49°C (32°F-120°F)

Humidity: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93%RH Maximum (non-condensing)

Mechanical Specifications

Dimensions (plastic enclosure, painted): . . . . 125 mm (W) × 220mm (H) × 31mm (D) / 4.9" × 8.7" × 1.2"

Weight (without battery): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .400g / 1.2oz

Simulated Telco Loop specifications (TIP/RING)

On-Hook Voltage: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V

Off-Hook Voltage (maximum): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22V

Loop Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25mA

Loop Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .600 Ohms

This equipment (3G4000) is fixed and shall be installed by Service Persons only (Service Person is defined as

a person having the appropriate technical training and experience necessary to be aware of hazards to

which that person may be exposed in performing a task, and of measures available to minimize the risks to

that person or other persons). It shall be installed and used within an environment that provides the

pollution degree max 2, over voltages category II, in non-hazardous, indoor locations only. This manual shall

be used with the Installation Manual of the relevant alarm control panel. All instructions specified within that

manual must be observed.

C24 Communications Enrolment

The 3G4000 requires enrolment with C24 Communications to operate. For more information, please visit

www.connect24.com, contact C24 Communications customer service at 1-888-251-7458 (US) / 1-888-955-

5583 (Canada) or contact the central station to inquire if they are a C24 Communications Master Reseller.

NOTES: Enrollment with C24 Communications should be performed before turning on the 3G4000 unit.

Before inserting or removing the SIM card, please ensure the unit is turned off.

STEP 1 - Initialize the 3G4000 with C24 Communications

The 3G4000 can be initialized with C24 Communications by:

web - www.connect24.com

mobile - m.connect24.com

To complete enrolment, a C24 profile, installer ID/PIN (or web credentials) and the 20-digit SIM number are

required.

NOTE: The SIM activation process with the cellular carrier typically takes between five and ten minutes

to complete.

STEP 2 - Determine the Best Signal Location

1. Remove the front cover by inserting a screwdriver into each of the slots at the bottom of the enclosure

and pushing down.

2. Apply power (DC and/or battery). The 3G4000 is now in placement test mode.

STEP 2a – SIM card is activated.

The red LED will be on solid, the blue LED will be off and the signal strength LEDs will display the average

signal strength. In this state, the 3G4000 is registered to the cellular network.

(use separately listed control panel or power supply) or 

Installing the 3G4000

(use DSC ADP1320-NAx power adapter)

)