Anywire ASLINKAMP LA-A1AW 제품 설명서 - 페이지 7

{카테고리_이름} Anywire ASLINKAMP LA-A1AW에 대한 제품 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Anywire ASLINKAMP LA-A1AW 12 페이지. Anywireaslink system, analog input unit ch insulated type with 7-segment

페이지 인쇄

[Various settings]

■Item

Address setting

Parameter setting

■Common procedure for address writer operation

Be sure to connect to the AnyWireASLINK master unit to use.

The operation requires the address writer ARW-03 (Ver.2.10 or

higher) or ARW-04 (Ver.04-1.00 or higher).

Refer to the address writer's Products Guide for details of the

operation method.

1. Connect the AnyWireASLINK slave to the master unit of the

AnyWireASLINK system.

Transmission signal is required to write and read setting items.

Set with the address writer while supplying the transmission signal to the

transmission lines (DP, DN) of the terminal.

Transmission

signal

Analog input unit

* Make sure to use a 24V DC stabilized power supply for the power supply to be connected.

2. Setting is required for all AnyWireASLINKs devices.

Open the protection cover of the set analog input unit and direct the

address writer to the setting port of the unit as shown in Fig.1 to set.

(Put the light emitting and receiving surface as close to the setting port as

possible.) Close the cover of the other units which are not set.

Setting port

LINK

ALM

Fig. 1

Analog port

e-CON (3P)

Address setting

■Address No. setting

An address number is set as a beginning number from which part of the

transmission frame is occupied to the unit.

Set any address number other than "255." The weight is "bit."

The factory address-number setting of the unit is

CAUTION

"255," which means no setting.

In this state, do not perform an address automatic

recognition (refer to the Manual of the master unit).

If the address number setting is "255," the unit

cannot perform an input/output operation.

Make sure to use the terminal after setting the

address number within the range of "0 to 254."

Ex.) Address correspondence of a quadruple analog input unit

AnyWire address

Input

"0" "16" "32" "48"

Setting address

Red: DP

AnyWireASLINK

Master

Black: DN

24V DC*

Setting port

When setting,

open the protection

cover.

Parameter setting

■Input specifications setting

Set the input speci cations of the analog.

- Address writer (ARW-04, ARW-03): Parameter 01

Variable

speci cations

0-10V

0-5V

1-5V

0-20mA

4-20mA

When receiving the transmission signal and starting, the unit displays set

input speci cations for about 3 seconds and then switches them to actual

input value display.

■Setting of average number of moving times

This is the setting of the average number of moving times of analog input.

The average value of the number of setting times +1 is adopted.

- Address writer (ARW-04, ARW-03): Parameter 03

Variable

Average number of moving times once

0～31

Setting range 0 to 31 (Average of MAX 32 times)

■Address/parameter automatic setting (base unit only)

This is a function to automatically re ect an address and parameter setting

set to the base unit to the extension unit.

- Address writer (ARW-04, ARW-03): Parameter 17

Variable

Automatic setting unavailable

Address/Parameter setting to the base unit and extension unit

respectively.

Address automatic setting

Only the address is automatically assigned to extension units

extended from the base unit in series.

Parameter automatic setting

Only the parameter is automatically re ected to extension units

extended from the base unit.

Address/parameter automatic setting

The address is automatically assigned to extension units extended

from the base unit in series.

The parameter is automatically re ected to extension units extended

from the base unit.

When this automatic setting mode becomes available (value 1, 2, 3), the

255

address or parameter set to the base unit is automatically assigned to

extension units.

They are assigned even when LB-A12W is mixed.

In the "reference shift mode," however, only ON or OFF is re ected.

Set renewal of the reference value individually.

Ex.) Parameter 17

In the case of value 1

Setting address

-L*A1AW 7/12-

Input

7-segment display

Before shipment: 0

Average number of moving times

Address/parameter automatic setting (base unit only)

Before shipment: 0

Assignment

"16"

"0"

LED

indication

V ON

LINK

ALM

V ON

LINK

ALM

V ON

LINK

ALM

mA ON

LINK

ALM

mA ON

LINK

ALM

Before shipment: 0

Supply

Extension

Supply

Base