Anywire ASLINKSENSOR BS-K4117-M 1K Series 제품 설명서 - 페이지 8

{카테고리_이름} Anywire ASLINKSENSOR BS-K4117-M 1K Series에 대한 제품 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Anywire ASLINKSENSOR BS-K4117-M 1K Series 9 페이지.

페이지 인쇄

[Troubleshooting]

If the followings are displayed on the LEDs of this product, take

measures as shown below.

LINK

ALM

○

Off

●

○

Off

◎

○

◎

Flashing

Off

(0.5 seconds

alternately)

－

◎

Flashing

(On for

0.2 seconds,

off for

1.0 seconds)

◎

－

●

Flashing

◎

－

◎

Flashing

(0.1 seconds

alternately)

When the following error is indicated on the address writer, take

measures as shown below.

Indication

Cause

[E-0303]

The set parameter is incorrect.

Take measures as follows in the following case.

Symptom

Detection cannot be

- Is the detected metal in the appropriate location?

performed.

→ Make adjustments so that the detected metal is within an appropriate range

from the ASLINKSENSOR detection surface.

- Is wiring correct?

→ Con rm that the ASLINKSENSOR transmission line is correctly connected

to the AnyWireASLINK transmission line (DP, DN).

- Are the AnyWireASLINK master unit and slave unit powered by a power supply

with the appropriate capacity?

→ Con rm the power supply.

- Did you perform teaching?

→ Perform teaching settings with the work that is actually detected.

- Are you using within the rated detection range?

→ Use within the rated range.

Setting cannot be

- Is wiring correct?

performed with

→ Recon rm the ASLINKSENSOR transmission line connection.

the address writer.

- Is power fed to the AnyWireASLINK system?

→ Con rm the power supply.

- Is the set parameter correct?

→ Check the parameter and set the correct parameter.

[Parameters and items]

Parameter

Variable

[01.]

Threshold

Set the threshold of the sensing level

0 - 100%

to judge presence/absence of detection.

[02.]

0 - 100%

Set change amount of sensing level

Hysteresis

required to turn detection state ON to OFF.

[03.]

Set an upper limit for the alarm

0 - 100%

Alarm value Hi

judgment value.

[04.]

Set a lower limit for the alarm

Alarm value Lo

0 - 100%

judgment value.

[05.]

Set a monitor time for the alarm

Alarm value

3-255

judgment value. (1 = 100ms)

monitor time

[06.]

Normally open

Normally open/

Normally close

[07.]

Simple mode

Operation

Normal mode

mode

[10.]

Delay timer disabled

Delay timer

ON/OFF

ON delay timer

OFF delay timer

ON/OFF delay timer

[11.]

Delay timer

0 - 255

Set the delay time. (1 = 10ms)

value

Cause

Measures

- ASLINKSENSOR is

- Con rm that there is no

not connected to an

disconnection between the

AnyWireASLINK

ASLINKSENSOR and the

system.

AnyWireASLINK system, and recover

- Power supply for the

the connection.

AnyWireASLINK

- Con rm the power status of the

system itself is not

AnyWireASLINK system, and turn on

turned on.

the power.

- Directly connected to

- Re-connect to the AnyWireASLINK

24-0V power supply.

system.

- The ASLINKSENSOR

- Set any address number other than

maintains the

255.

address number 255

(default setting).

- The ASLINKSENSOR

- Look for the other unit which has the

has an address

same error indication, and set any

redundant with

address number different from it.

another unit.

- Transmission signal

- Decrease the number of units

level reduction has

connected to the same

been detected.

AnyWireASLINK system.

- Shorten the transmission line

between the ASLINKSENSOR and

the master unit.

- The sensing level

- Con rm the ASLINKSENSOR status,

has been reduced.

adjust the position, and clean the

detection surface.

- Teaching is not

- Make sure to perform teaching

normally operated.

operation again.

Measures

Check the parameter and set the correct

parameter.

Measures

Details

[Speci cations]

■General Speci cations

Ambient temperature/humidity for use

Ambient temperature/humidity for storage

Atmosphere for use

Altitude of use *

Pollution level *

*1 Do not use or store the AnyWireASLINK device in an environment pressurized equal to

or higher than the atmospheric pressure at an altitude of 0m. Doing so could cause a

malfunction.

*2 Index that indicates the occurrence of conductive material in the environment where

the device is used.

Contamination level 2 indicates that only non-conductive contamination occurs.

However, incidental condensation could create temporary conductivity in this

environment.

■Transmission speci cations

Power supply voltage

for use

Transmission method

Synchronization method

Transmission procedure

Connection mode

Number of connection points

Number of units connected

RAS feature

■Individual speci cations

Number of occupied points

Consumption current

Detection method

Shield presence/absence

Detection target *

Standard detection objects

Detection distance

(At ambient temperature

of 23°C)

Stable detection

distance

Hysteresis

Response time *

Default

Impact from

variable

temperature

M12 : 18

M18 : 24

M30 : 26

Impact from voltage

Protective structure

M12 : 19

Mass

M18 : 25

(This product/Cable)

M30 : 27

Mass

(Nuts/Washer)

*3 The detection distance depends on the material.

*4 Time from when ON or OFF is detected until the transmission signal is transmitted.

The time combining this time and the transmission 2 cycle time is the transmission

delay time.

-BSK4117M**1K 8/9-

-10 - 60°C, 10 - 90%RH (No condensation)

-25 - 75°C, 10 - 90%RH (No condensation)

No corrosive gas

0 to 2000m

2 or less

Voltage 24V DC +15% to -10% (21.6 to 27.6V DC

Ripple of 0.5Vp-p max.

DC power supply superimposed total frame/cyclic method

Frame/bit synchronization method

Dedicated protocol

Bus type

(Multi-drop method, T-branch method, Tree branch method)

512 max. (IN: 256, OUT: 256)

Up to 128 units

Transmission line disconnection detection,

transmission line short-circuit detection,

transmission power supply reduction detection,

ID redundancy, ID not set detection

One-point input

Supplied via AnyWireASLINK transmission signal (DP, DN)

M12: 13mA

M18: 13mA

Electromagnetic induction detection

Shield type

Non-magnetic metal/Magnetic metal

M12: Aluminum 12×12×3mm M30: Aluminum 30×30×3mm

M18: Aluminum 18×18×3mm

M12: 2mm (max.)

M18: 5mm (max.)

M12: 0 to 1.6mm

M18: 0 to 4.5mm

Depends on parameter setting

Max. 10ms

Detection distance at 23°C

M12: Within ±20%

M18: Within ±10%

Within ±1% of the detection distance with the

AnyWireASLINK master supplied power voltage

within range of 27.6 to 21.6V

IP67

M12: Approx. 37g

M18: Approx. 49g

M12: Approx. 8g

M18: Approx. 19g

M30: 13mA

M30: 10mm (max.)

M30: 0 to 9.0mm

M30: Within ±10%

M30: Approx. 105g

M30: Approx. 41g