Casio 2590 사용자 설명서

{카테고리_이름} Casio 2590에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Casio 2590 3 페이지. 2590; 2591

페이지 인쇄

USER'S GUIDE 2590/2591

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your

purchase, be sure to carefully read this manual and keep it on hand for later reference

when necessary.

Expose the watch to bright light to charge its battery before using it.

You can use this watch even as its battery is being charged by exposure to bright

light.

• Be sure to read "Battery" of this manual for important information you

need to know when exposing the watch to bright light.

If the display of the watch is blank...

If the Power Saving on (P.SAVE) indicator flashes on

the display, it means that the display is blank because

the watch's Power Saving function has turned off

the display to conserve power. Power Saving

automatically turns off the display and puts the watch

into a sleep state whenever your watch is left for a

certain period where it is dark.

• The initial factory default setting is Power Saving on.

• The watch recovers from the sleep state if you move it

to a well-lit area, if you press any button, or if you

angle the watch towards your face for reading.

• See "Power Saving Function" for more

information.

General Guide

• Press C to change from mode to mode.

• In any mode, press B to illuminate the display.

Timekeeping Mode

Press

Timekeeping

Use the Timekeeping Mode to set and view the current

PM indicator

time and date.

Day of week

To set the time and date

Month – Day

1. In the Timekeeping Mode, hold down A until the

seconds start to flash, which indicates the setting

screen.

2. Press C to move the flashing in the sequence shown

below to select other settings.

Seconds

Day

Hour : Minutes Seconds

3. When the setting you want to change is flashing, press D to change it as

described below.

To change this setting

Press D to reset to 00.

Seconds

Press D to increase the setting.

Hour, Minutes, Year, Month, Day

• Pressing D while the seconds are in the range of 30 to 59 resets them to 00 and

adds 1 to the minutes. In the range of 00 to 29, the minutes are unchanged.

4. Press A to exit the setting screen.

• The day of the week is automatically displayed in accordance with the date (year,

month, and day) settings.

• The year can be set in the range of 2000 to 2099.

• The watch's built-in full automatic calendar automatically makes allowances for

different month lengths and leap years. Once you set the date, there should be no

reason to change it except after you have the watch's battery replaced or when

battery power drops to Level 4.

To toggle between 12-hour and 24-hour timekeeping

In the Timekeeping Mode, press D to toggle between 12-hour timekeeping and

24-hour timekeeping.

• With the 12-hour format, the PM (Module 2590: PM/Module 2591: P) indicator

appears to the left of the hour digits for times in the range of noon to 11:59 p.m. and

no indicator appears to the left of the hour digits for times in the range of midnight to

11:59 a.m.

• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without

any indicator.

• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

applied in all other modes.

Alarm Mode

Hour

Minutes

Month

Year

Perform this button operation

About This Manual

• The operational procedures for Modules 2590 and 2591

are identical. All of the illustrations in this manual show

Module 2590.

• Button operations are indicated using the letters shown

in the illustration.

• Each section of this manual provides you with the

information you need to perform operations in each

mode. Further details and technical information can be

[Module 2590]

found in the "Reference" section.

[Module 2591]

• In any mode, hold down C for about two seconds to return to the Timekeeping

Mode.

Countdown Timer

Stopwatch Mode

Mode

Alarms

You can set up to five independent multi-function alarms

Alarm date

with hour, minutes, month, and day. When an alarm is

(Month-Day)

turned on, the alarm tone sounds when the alarm time is

reached. One of the alarms can be configured as a

snooze alarm or a one-time alarm, while the other four are

one-time alarms.

You can also turn on an Hourly Time Signal that causes

the watch to beep twice every hour on the hour.

• There are five alarms numbered

configure Alarm

alarm. Alarms

Alarm time

alarms only.

(Hour : Minutes)

• Alarm settings (and an Hourly Time Signal setting) are

available in the Alarm Mode, which you enter by

Alarm number

pressing C.

Alarm Types

The alarm type is determined by the settings you make, as described below.

• Daily alarm

Set the hour and minutes for the alarm time. This type of setting causes the alarm to

sound everyday at the time you set.

• Date alarm

Set the month, day, hour and minutes for the alarm time. This type of setting causes

the alarm to sound at the specific time, on the specific date you set.

• 1-Month alarm

Set the month, hour and minutes for the alarm time. This type of setting causes the

alarm to sound everyday at time you set, only during the month you set.

• Monthly alarm

Set the day, hour and minutes for the alarm time. This type of setting causes the alarm

to sound every month at time you set, on the day you set.

To set an alarm time

1. In the Alarm Mode, use D to scroll through the alarm

screens until the one whose time you want to set is

displayed.

• To set a one-time alarm, display one of the screens indicated by an alarm number

from

through

. To set the snooze alarm, display the screen indicated by

2. After you select an alarm, hold down A until the hour setting of the alarm time

starts to flash, which indicates the setting screen.

• This operation automatically turns on the alarm.

3. Press C to move the flashing in the sequence shown below to select other

settings.

Hour

Minutes

Dual Time Mode

through

. You can

as a snooze alarm or a one-time

through

can be used as one-time

Press

Month

Day