Danfoss ECL Comfort 210 운영 매뉴얼 - 페이지 5

{카테고리_이름} Danfoss ECL Comfort 210에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Danfoss ECL Comfort 210 10 페이지. Extended heat cut-out
Danfoss ECL Comfort 210에 대해서도 마찬가지입니다: 사용자 설명서 (12 페이지), 사용자 설명서 (12 페이지), 사용자 설명서 (6 페이지), 설치 매뉴얼 (4 페이지), 설치 매뉴얼 (20 페이지), 운영 매뉴얼 (16 페이지), 설치 매뉴얼 (7 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (16 페이지), 마운팅 매뉴얼 (16 페이지)

페이지 인쇄
Danfoss ECL Comfort 210 운영 매뉴얼
ECL Comfort 210, 296 and 310, return temperature limitation

2.0 Settings

2.1 Return temperature limitation in a master / slave system
The circuit 1 menu for return temperature limit parameters
contains an additional parameter "DHW, ret. T limit" (= Domestic
Hot Water, return temperature limit).
When a slave in a master / slave system is in DHW-tank heating /
charging mode, the desired flow temperature value is transferred to
the master. The master will react by controlling a flow temperature
being a number of degrees higher ("Demand offset") than the
desired flow temperature from the slave.
When the master is fulfilling a DHW-tank heating / charging
demand from a slave, the return temperature limitation can be
done in relation to a set value.
The return temperature limitation will always be related to the
highest limitation value.
An example: Return temperature limitation (DHW) = 55 °C and
return temperature limitation (heating) = 60 °C.
The result will be a return temperature limitation at 60 °C.
If the master is not controlling a desired flow temperature from a
slave, the return temperature limitation can be done in relation to
the outdoor temperature.
The parameter "DHW, ret. T limit" is not present in applications with
DHW-tank heating / charging.
Examples: A237, A247, A367, A377.
MENU > Settings > Return temperature limitation in a master /
slave system
DHW, ret. T limit
Circuit
1
When an addressed slave is active in DHW-tank heating / charging, the
return temperature limitation in the master can be set.
Notes:
•
The master circuit must be set to react on the desired flow temperature
in the slave(s). See "Demand offset" (ID 11017).
•
The slave(s) must be set to send its / their desired flow temperature to the
master. See "Send desired T" (ID 1x500).
OFF:
No influence from slaves. The return temperature
limitation is related to settings in "Return limit".
10 –
Return temperature limitation value when slave is in
110 °C:
DHW tank heating / charging operation.
VI.GU.W2.02
11029
Setting range
Factory setting
OFF / 10 – 110 °C
OFF
# 1 # = Master, example A266, address 15
# 2 # = Slave, example A237, address 9
# 3 # = Slave, example A367, address 6
Some examples of applications with DHW-tank heating / charging are:
•
A217, A237, A247, A367, A377
© Danfoss | 2017.08 | 5