Danfoss ECL Comfort 210 Kullanım Kılavuzu - Sayfa 5

Termostat Danfoss ECL Comfort 210 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Danfoss ECL Comfort 210 10 sayfaları. Extended heat cut-out
Ayrıca Danfoss ECL Comfort 210 için: Kullanıcı Kılavuzu (12 sayfalar), Kullanıcı Kılavuzu (12 sayfalar), Kullanıcı Kılavuzu (6 sayfalar), Kurulum Kılavuzu (4 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kullanım Kılavuzu (16 sayfalar), Kurulum Kılavuzu (7 sayfalar), Kurulum Kılavuzu (16 sayfalar), Kurulum Kılavuzu (16 sayfalar), Kurulum Kılavuzu (16 sayfalar), Kurulum Kılavuzu (16 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (16 sayfalar), Montaj Kılavuzu (16 sayfalar)

Sayfayı Yazdır
Danfoss ECL Comfort 210 Kullanım Kılavuzu
ECL Comfort 210, 296 and 310, return temperature limitation

2.0 Settings

2.1 Return temperature limitation in a master / slave system
The circuit 1 menu for return temperature limit parameters
contains an additional parameter "DHW, ret. T limit" (= Domestic
Hot Water, return temperature limit).
When a slave in a master / slave system is in DHW-tank heating /
charging mode, the desired flow temperature value is transferred to
the master. The master will react by controlling a flow temperature
being a number of degrees higher ("Demand offset") than the
desired flow temperature from the slave.
When the master is fulfilling a DHW-tank heating / charging
demand from a slave, the return temperature limitation can be
done in relation to a set value.
The return temperature limitation will always be related to the
highest limitation value.
An example: Return temperature limitation (DHW) = 55 °C and
return temperature limitation (heating) = 60 °C.
The result will be a return temperature limitation at 60 °C.
If the master is not controlling a desired flow temperature from a
slave, the return temperature limitation can be done in relation to
the outdoor temperature.
The parameter "DHW, ret. T limit" is not present in applications with
DHW-tank heating / charging.
Examples: A237, A247, A367, A377.
MENU > Settings > Return temperature limitation in a master /
slave system
DHW, ret. T limit
Circuit
1
When an addressed slave is active in DHW-tank heating / charging, the
return temperature limitation in the master can be set.
Notes:
•
The master circuit must be set to react on the desired flow temperature
in the slave(s). See "Demand offset" (ID 11017).
•
The slave(s) must be set to send its / their desired flow temperature to the
master. See "Send desired T" (ID 1x500).
OFF:
No influence from slaves. The return temperature
limitation is related to settings in "Return limit".
10 –
Return temperature limitation value when slave is in
110 °C:
DHW tank heating / charging operation.
VI.GU.W2.02
11029
Setting range
Factory setting
OFF / 10 – 110 °C
OFF
# 1 # = Master, example A266, address 15
# 2 # = Slave, example A237, address 9
# 3 # = Slave, example A367, address 6
Some examples of applications with DHW-tank heating / charging are:
•
A217, A237, A247, A367, A377
© Danfoss | 2017.08 | 5