APP SPEC Pak 조립 지침 - 페이지 2

{카테고리_이름} APP SPEC Pak에 대한 조립 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. APP SPEC Pak 2 페이지. High power panel mount receptacle

페이지 인쇄

Step 4 Insert Powerpole

•

With Hood up, slide Powerpole

right side, aligning the holder posts with the grove in Powerpole

•

Orient the remaining holder half with on the right side (See Figure 4)

•

Slide remaining half into the assembly, inserting the holder posts into the Powerpole

holes and aligning the tongues and grooves on the holder halves

Step 5 Install Receptacle housing on the panel:

•

Clean and dry the panel surface thoroughly

•

Orient housing with APP logo facing up

•

Sandwich panel mount receptacle gasket between the panel and the receptacle shell

(See Figure 5)

•

Secure the panel mount receptacle and gasket to the panel with size #10 or M5

screws (not included) in an alternating manner. Suggested Torque: 15-20 in-lbs (1.7-

2.2 N-M)

Step 6 Install crimped signal contacts into the holder and

crimped power contacts into the connector housings.

•

Pull wires through the panel

•

Orient the insert holder with the to the right (See Figure 6)

•

Snap the crimped signal contacts into the appropriate holes in the back of the holder

halves (See Figure 7). A tactile snap will be felt when contact is latched.

•

Insert crimped power contacts into the appropriate Powerpole® housing until the con-

tact lip snaps over the edge of the spring (See Figure 8)

•

Repeat until all power and/or signal contacts have been installed into the housing

Step 7 Install insert holder into the receptacle shell

•

Verify that the O-Ring is properly seated in the receptacle shell

•

Secure insert holder to the panel mount receptacle by tightening the screws in an

alternating manner. Torque: 13 in-lb (1.4 N-M)

Figure 7

REGISTRATION

"Anderson Power Products", "APP" are registered U.S. and foreign trademark of Anderson Power Products

PATENTS AND TRADEMARKS

HEADQUARTERS: Anderson Power Products®, 13 Pratts Junction Road, Sterling, MA 01564-2305 USA T:978-422-3600 F:978-422-3700

EUROPE: Anderson Power Products® Ltd., Unit 3, Europa Court, Europa Boulevard, Westbrook, Warrington, Cheshire, WA5 7TN United Kingdom T: +44 (0) 1925 428390 F: +44 (0) 1925 520203

ASIA / PACIFIC: IDEAL Anderson Asia Pacific Ltd., Unit 922-928 Topsail Plaza, 11 On Sum Street, Shatin N.T., Hong Kong T:+(852) 2636 0836 F:+(852) 2635 9036

CHINA: IDEAL Anderson Technologies (Shenzhen) Ltd., Block A8 Tantou Western Industrial Park, Songgang Baoan District, Shenzhen, PR. China 518105 T: +(86) 755 2768 2118 F: +(86) 755 2768 2218

TAIWAN: IDEAL Anderson Asia Pacific Ltd., Taiwan Branch, 4F.-2, No.116, Dadun 20th St., Situn District, Taichung City 407, Taiwan (R.O.C.) T: +(886) 4 2310 6451 F:+(886) 4 2310 6460

SPEC Pak

High Power Panel Mount Receptacle

™

block into Powerpole

block into the holder half marked with on the

Latched

Contact

Figure 8

www.andersonpower.com

Page 2

Holder:

holes (See Figure 4)

, 213 Pratts Junction Road, Sterling, MA 01564-2305 USA www.andersonpower.com

Figure 4

Panel Hardware

Not Included

Figure 5

Sockets

Figure 6

Suggested Hood

Orientation for

Receptacle

Groove

Assembled Holder

Flatness

[ 0.002]

0.05

Gasket

Pins

14938

1S6555 REV 01