Datalogic Memor 사용자 설명서
{카테고리_이름} Datalogic Memor에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Datalogic Memor 2 페이지. Multi-battery charger
Datalogic Memor에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (2 페이지), 매뉴얼 (2 페이지), 빠른 매뉴얼 (2 페이지)
페이지 인쇄
Datalogic Memor™ Single Ethernet Cradle
Read this manual carefully before performing any type
of connection through the Datalogic Memor™ Single
Ethernet Cradle.
The user is responsible for any damages caused by
NOTE
incorrect use of the equipment or by inobservance of the
indication supplied in this manual.
Do not attempt to disassemble the Datalogic Memor™
Single Ethernet Cradle, as it does not contain parts that
can be repaired by the user. Any tampering will invalidate
the warranty.
NOTE
The Datalogic Memor™ Single Ethernet Cradle paired with one Datalogic
Memor™ mobile computer builds a reading system for the collection,
decoding and transmission of barcoded data.
The communication between the mobile computer and host PC through
the Datalogic Memor™ Single Ethernet Cradle may occur also by using
the standard ActiveSync® connection.
D
A
C
Figure 1 – Datalogic Memor™ Single Ethernet Cradle
A)
LED Indicators
E)
Power Jack
B)
Spare Battery Slot
F)
Ethernet Port with LED indicators
C)
Mini USB Connector
G)
Switch Ethernet/USB
D)
RS232 Connector
The
Datalogic
Memor™
Single
Ethernet
communication adapter between the host computer and the Datalogic
Memor™ mobile computer. Power supply is required to be connected to
the Cradle only for ethernet communication.
Since the Datalogic Memor™ Single Ethernet Cradle also functions as a
battery charger, a power supply is required for battery recharging
operations, both for the mobile computer and spare battery pack
recharging. The spare battery pack recharging slot can supply a 1000
mAh as well as a 2000 mAh Battery pac.
822000820
By inserting the Datalogic Memor™ into the cradle, data can be
transmitted to the host and its battery begins charging if the power supply
is connected. In addition, a spare battery can be charged by inserting it
into the slot at the back of the Datalogic Memor™ Single Ethernet Cradle
as shown in the following figure.
Spare battery
Charge Slot with
Spare Battery
Inserted
Figure 2 – Datalogic Memor™ Single Ethernet Cradle Charging and
B
The LEDs positioned on the front part of the Datalogic Memor™
Ethernet Cradle (see figure below) indicate the cradle and spare
E
battery charger status:
Power LED
G
F
Cradle
is
a
serial
Front LED indicators
LED
Charger
Power
*
During charging, the LED may turn off to indicate a temporary
suspension of charging.
Data Transmission and
Mobile Computer Battery
Charging
Communication
Spare Battery
Charger LED
Figure 3 - LED Indicators
STATUS
Red Constant
Spare battery charging*
Green Constant
Spare
battery
charge
completed
Green
it is constant when the
cradle is powered
Ethernet Connector LED Indicators
Solid Green
Link established
Ethernet
Green LED
Flashing Green
Link activity
(left)
Off
No link established
Ethernet
Off
10 Mb connection
Yellow LED
Solid Yellow
100 Mb connection (this model is not
(right)
available)
CONNECTIONS
Connections should always be made with power OFF!
CAUTION
USB CONNECTION
The Datalogic Memor™ Single Ethernet Cradle can be connected to the
host by means of any standard Mini USB cable.
Once the host has been turned on, insert the Datalogic Memor™
mobile computer into the cradle.
A
B
D*
Figure 4 - USB Connection
A)
Host Computer
C)
Datalogic
Ethernet Cradle
B)
Std
Mini
USB
(i.e.
D)
*Power Supply (only necessary
94A051016 CAB-421)
for battery charging)
*
Recommended power supply: 94ACC1324 PG5-30P35 AC/DC
POWER SUPPLY EU/USA PLUG.
Be sure that the switch is in the "USB" position.
During switch operation from USB position to Ethernet
position and vice versa the mobile computer must not be
inserted in the cradle.
NOTE
C
Memor™
Single