Datalogic Memor 빠른 매뉴얼
{카테고리_이름} Datalogic Memor에 대한 빠른 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Datalogic Memor 2 페이지. Multi-battery charger
Datalogic Memor에 대해서도 마찬가지입니다: 사용자 설명서 (2 페이지), 빠른 시작 매뉴얼 (2 페이지), 매뉴얼 (2 페이지)
페이지 인쇄
Datalogic Memor™ Multi-Battery Charger
Power on
Battery Charging
State LEDs
Figure 1
The Datalogic Memor Multi-Battery Charger, with its 4 slots,
allows you to charge the Datalogic Memor battery packs.
The Datalogic Memor Multi-Battery Charger is compatible with
the following batteries:
−
94ACC1367 Dl-Memor Large Capacity Battery Cvr2,
ETI CA Battery Inc. P/N BP08-000610, 3.7V 2000mAh TYP
−
94ACC1368 Dl-Memor Standard Battery Cvr2,
ETI CA Battery Inc. P/N BP08-000600, 3.7V 1100mAh TYP
−
94ACC0083 Memor X3 Standard Battery
Model: Standard, Memor X3, 3.7V 1430 mAh TYP
−
94ACC0084 Memor X3 Large Capacity Battery
Model: Extended, Memor X3, 3.7V 2300mAh TYP
Annual replacement of rechargeable battery
pack avoids possible risks or abnormalities and
ensures maximum performance.
CAUTION
822000924
(Rev. A)
Nov. 2017
SET UP AND USE
Plug the power supply into the connector positioned on the
Datalogic Memor Multi-Battery Charger base. Then plug the
power supply into a socket.
Figure 2
Insert the battery pack into one of the free slots with the battery
contacts oriented toward the charger back by simply pressing
downward until the battery snaps in place.
Figure 3
The Datalogic Memor Multi-Battery Charger
could get warm during charging, this is normal
and does not mean a malfunction.
NOTE
Installing, charging and/or any other action
should be done by authorized personnel and
following this manual.
WARNING
The battery pack may get hot, explode, ignite,
and/or cause serious injury if exposed to
abusive conditions.
If the battery pack is replaced with an improper
type, there is risk of explosion.
Do not place the battery pack in or near a fire
or heat; do not place the battery pack in direct
sunlight, or use or store the battery pack inside
unventilated areas in hot weather; do not place
the battery pack in microwave ovens, dryer,
high
pressure
containers,
cookware or similar device. Doing so may
cause the battery pack to generate heat,
explode or ignite. Using the battery pack in this
manner
may
also
result
performance and a shortened life expectancy.
Use only a Datalogic approved power supply.
The use of an alternative power supply will void
the product warranty, may cause product
damage and may cause heat, explode or ignite.
The area in which the units are charged should
be clear of debris and combustible materials or
chemicals.
Immediately discontinue use of the battery
pack if, while using, charging or storing the
battery pack, the battery pack emits an unusual
smell, feels hot, changes colour or shape, or
appears abnormal in any other way.
Do not short-circuit the battery pack contacts
connecting the positive terminal and negative
terminal. This might happen, for example, when
you carry a spare battery pack in your pocket
or purse; accidental short–circuiting can occur
when a metallic object such as a coin, clip, or
pen causes direct connection of the contacts of
the battery pack (these look like metal strips on
the battery pack). Short–circuiting the terminals
may damage the battery pack or the connecting
object.
on
induction
in
a
loss
of