AUSTRALIAN MONITOR TX8202 사양 - 페이지 2

{카테고리_이름} AUSTRALIAN MONITOR TX8202에 대한 사양을 온라인으로 검색하거나 PDF를 다운로드하세요. AUSTRALIAN MONITOR TX8202 2 페이지. 8 channel 1 ru mixer
AUSTRALIAN MONITOR TX8202에 대해서도 마찬가지입니다: 운영 매뉴얼 (11 페이지), 사양 (2 페이지)

페이지 인쇄

Engineered and Distributed by AUDIO TELEX COMMUNICATIONS PTY LTD

NSW Tel: (02) 9647 1411 Fax: (02) 9648 3698 VIC Tel: (03) 9890 7477 Fax: (03) 9890 7977 QLD Tel: (07) 3852 1312 Fax: (07) 3252 1237 WA Tel: (08) 9228 4222 Fax: (08) 9228 4233

Tas Tel: (03) 6228 6373 Fax: (03) 6278 1063 SA Tel: (08) 8352 4444 Export Enquiries: [email protected] Website: www.australianmonitor.com.au

Frequency Response

Total Harmonic Distortion

Signal To Noise Ratio

Tone Controls

Bass @ 100Hz - Boost +12dB, Cut -12dB; Treble @ 10kHz - Boost +10dB, Cut -10dB

Inputs

4 active balanced mic/line inputs with 3 pin XLR female sockets (200 - 600 Ohms)

Maximum Input Level is 500mV; 4 Stereo Line inputs with dual female RCAs (47K Ohms)

Input Sensitivity

Phantom Power

Outputs

Left and Right Master Outputs, 3 pin XLR male sockets. (1.5V @ 600 Ohms.)

Stereo Tape Output, dual female RCA connectors. (400mV @ 10K Ohms)

Controls

Level Control per channel, Recessed Treble, Bass and Pan Controls per channel,

Indicators

Power "on" orange LED, 7 segment LED meters for both L and R outputs

Power Source

Power Consumption

Dimensions/Weight

ARCHITECTURAL AND ENGINEERING SPECIFICATIONS

The mixer shall have 4 balanced mic/line inputs and 4 stereo line inputs. The mic/line channels shall be

balanced and feature 3 pin female XLR sockets. The stereo line channels shall have dual female RCA

sockets. Each channel shall include tamper resistant treble, bass, and pan controls. The ﬁ rst four channels

feature a line level direct output which can be used to feed additional ampliﬁ ers, mixers or recording

devices. An internal jumper shall allow the ﬁ rst four inputs to be removed from the master left/right outputs

whilst still retaining their direct output function. The equalisation per channel shall provide 12dB cut or

boost at 100Hz and 10dB cut or boost at 10kHz. The master section shall include individual level controls

for both the Left and Right outputs and shall also include two 7 segment output level LED meters. The

master outputs shall be balanced 3 pin XLR male sockets, and dual RCA female sockets for the stereo

tape output. A ¼" stereo headphone socket shall be included for monitoring. The mixer shall include on

board muting card, as well as a option for 4 tone generator modules and remote master VCA control.

The mixer shall be of high quality, suitable for both live and commercial applications. It should have ample

headroom and a frequency response of no less than 50Hz - 15kHz (±3dB). Total Harmonic distortion shall

be no more than 0.1% at 1kHz. The S/N ratio shall be -74dBV or better. Phantom Power of no less than

15V DC shall be available on all microphone inputs. An internal switch to disable the phantom power on

any of the mic/line channels shall also be included. The unit shall be packaged in a rugged 1 RU metal

chassis suitable for desk or rack mounting.

The mixer shall be an Australian Monitor Installation Series model TX8202.

(ABN 78 001 345 482)

-74dBV (all channels at centre position)

Line 1–4: 150mV - 1V @ 47K Ohms; Line 5–8: 125mV @ 47K Ohms

15V DC on all mic channels (switchable)

Stereo Headphone Output, 1/4" stereo socket. (3.5V @ 600 Ohms)

Four direct line level outputs (600mV @ 10K Ohms)

Left and Right Master Level Controls

AC: 240V - 50Hz or 110V - 60Hz (special order) 3 pin IEC connector

44mm H x 482mm W x 250mm D (Chassis dimensions only). 4kg

, 149 Beaconsfield Street, Silverwater, Sydney, NSW, 2128

50Hz - 15kHz (± 3dB)

Less than 0.1% @ 1kHz

Maximum Input Level is 1.5V

Mic: 1mV @ 200 Ohms;

Maximum Output Level: +20dB;

7 Watts