BENDIX SV-1 SYNCHRO-SV-3 TRAILER RELEASE 매뉴얼 - 페이지 2
{카테고리_이름} BENDIX SV-1 SYNCHRO-SV-3 TRAILER RELEASE에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. BENDIX SV-1 SYNCHRO-SV-3 TRAILER RELEASE 6 페이지. Synchro valve, trailer release valve
페이지 인쇄
components. The air connection ports for SV-1
SV-4
valves are the same and are located in relatively the
™
same position on each model. All connections are pipe thread.
Lettering embossed in the valve body identifies two of the
four connection ports in these valves. Refer to the chart below
and figure one.
Air Connection
Body Ident. Thread Size
Air Supply
SUP
Delivery
DEL
Control
None
Exhaust
None
IMPORTANT: An exhaust check valve should be installed in
the threaded exhaust port of these valves when they are
mounted outside the cab in unprotected environments.
SV-1
™
Synchro Valve
1/8" PIPE THREAD
Note: Either style may be installed in the
SV-1
™
, SV-3
FIGURE 3 - EXHAUST CHECK VALVE STYLES
The SV-1
valve is a general purpose valve used in a variety
™
of applications on trucks, buses, tractors, trailers and
converter dollies. The SV-1
which both the SV-3
™
and SV-4
offered in a variety of pressure settings to accommodate
applications where automatic operation is required. It is easily
distinguished from the SV-3
size.
SV-3
™
Trailer Release Valve
While originally designed for automatic operation to
accomplish brake release on trailers without spring brakes,
the SV-3
valve can be used in any installation where its
™
single automatic pressure setting is advantageous. The
SV-3
valve is very similar in appearance to the SV-4
™
but can be distinguished by measuring the length and
diameter of the supply hex cap nut (1/4" PT supply port).
See the comparison chart for the dimensions.
SV-4
Trailer Release Valve
™
The SV-4
valve was designed primarily for use on trailer
™
converter dollies to minimize the possibility of false charging.
Like the SV-3
valve it can be used in other applications.
™
The SV-4
valve is the combination of two valves; an SV-3
™
valve and a single check valve. A typical installation is
illustrated in figure 4. The SV-4
from the SV-3
valve using the dimensions given in the
™
comparison chart. In addition, the tip of the check valve
contained in the SV-4
valve is visible at the bottom of the
™
¼" PT supply port.
2
, SV-3
™
1/4" PT
1/4" PT
1/4" PT
1/8" PT
1/8" PIPE THREAD
™
or SV-4
™
valves
valve is the base valve from
™
™
valves are derived. It is
and SV-4
valve by its smaller
™
™
™
valve can be distinguished
™
&
™
SV-3
Supply Cap Nut Dimensions
SV-3
SV-4
OPERATION
GENERAL
The SV-1
, SV-3
™
fashion. All can be connected in the air system so that other
valves control them. When connected in this non-automatic
mode the valve serves as a remote mounted, On-Off control.
They can also be installed so that they function automatically
or self actuate at a preset pressure. Automatic operation is
the most common application. Regardless of how they are
connected the internal valve operation is the same.
NON-AUTOMATIC (valve controlled remotely by another
valve)
With no air pressure present at the control port, supply port
air pressure and the inlet/exhaust valve spring hold the inlet
valve on its seat in the body. The piston is held away from
the inlet/exhaust valve by the piston spring, and the delivery
line is vented to atmosphere through the hollow exhaust
stem of the piston.
When sufficient air pressure is applied to the control port,
the control piston moves against the resistance of its return
spring. As the control piston moves, it contacts the exhaust
valve portion of the inlet and exhaust valve which seals the
hollow exhaust passage in the piston stem. Continued piston
movement drives the inlet valve from its seat and allows
supply air to flow through the body and out the delivery port.
When air pressure is removed from the control port, the
piston return spring and delivery port air pressure move the
piston away from the inlet/exhaust valve. As the piston moves,
the inlet valve re-seats itself preventing air flow to the delivery
port. Continued movement unseats the hollow exhaust
passage in the piston stem allowing delivery air to flow
through the stem and out the exhaust check valve.
valve
SINGLE CHECK VALVE
™
Note:
An SV-4
SV-1
™
FIGURE 4 - TRAILER CONVERTER DOLLY
™
/SV-4
™
Valve Comparison
Diameter Length
.8125"
1.162"
.94"
1.062"
, & SV-4
valves all operate in a similar
™
™
valve can be used in place of the
™
valve and single check valve shown here.
SV-1
™
SYNCHRO