Dymo LabelManager 100 사용자 설명서 - 페이지 3

{카테고리_이름} Dymo LabelManager 100에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Dymo LabelManager 100 6 페이지. Electronic labelmaker
Dymo LabelManager 100에 대해서도 마찬가지입니다: 사용 설명서 지침 (18 페이지)

페이지 인쇄

Introduction

The Dymo LM100 Electronic Labelmaker enables you to

create a wide variety of high quality self-adhesive labels of

up to 100 characters.

The Labelmaker uses 9mm (

cassettes in a number of label colours. Labels are back

slit for easy removal from the backing tape. Text can be

printed horizontally or vertically in a variety of sizes and

styles and is always centered on the label.

Warranty Registration

Please complete the warranty registration card and return

it to the relevant customer service address, within seven

days– see the warranty booklet for details.

Power Supply

BATTERIES

• Apply pressure to thumb catch and open hinged access

door – see fig A, page 2.

• Insert six size AA alkaline or re-chargeable Nickel-

cadmium batteries, observing the polarity markings

, and close cover.

• Remove batteries if the Labelmaker is to be unused for

some time.

AC ADAPTOR (optional)

• Connect the AC adaptor to socket B

adaptor plug disconnects the supply from the batteries.

• Unplug the AC adaptor from the Labelmaker before

disconnecting the mains power to the adaptor,

otherwise last label memory settings will be lost (see

also ON/OFF).

Changing the cassette

• Open hinged access door as above.

• Hold as shown, then lift cassette B

out.

• Ensure tape and ribbon B

cassette and tape passes between guideposts before

installing as shown. If necessary, turn spool B

clockwise to tighten ribbon.

• Insert cassette and push firmly C until it clicks into

place.

• Ensure tape and ribbon are positioned as shown

between pinch roller C

The Display

Box

Underline

CAPS on

–

CAPS

1 2 3 4 5 6 7 8

Shift on

The display shows:

") or 12mm (

") wide tape

. Inserting the

straight up and

are taut across mouth of

and print head C

Vertical

Italic

Outline

text

ITALIC

OUTLINE

VERT

LTH SET

Fixed label

CURSOR

length set

• Up to eight text characters, plus the cursor,

at one time.

Use

to move along the text.

• Eight indicators – as shown above.

• The display will flash if you press an incorrect key in a

function sequence.

Function keys

ON/OFF

Switches the power on and off.

• Switches off automatically after two minutes if no keys are

pressed. The last label created will be retained and

displayed when next turned on. Any stored label and

settings will be retained.

Note: If the batteries are removed for more than a few

seconds, all text and settings will be lost.

When power is restored, the display will show a flashing

cursor (no text) and the settings will be full height

standard width text with

CAPITALS

CAPS

• Press for all subsequent characters in UPPER CASE

(CAPITALS), as confirmed by the CAPS indicator in the

display.

• Press again to cancel and return to lower case.

SHIFT KEY

Dual action - either press and hold down or press and

release to remain in "shift" position. Press

to return to normal state.

• Use

before pressing an alphabet key to produce

an UPPER CASE (CAPS) character.

• For dual-purpose keys, press

the legend above the key.

• Pressing

while

character.

DELETE

DEL

• Press to delete the character to the left of the cursor, or to

exit certain function key operations.

CLEAR TEXT

• Press to clear all the current text and cancel any fixed

length setting, but leave the text size and other settings

unchanged. Also use to exit or clear certain function

key operations.

CURSOR KEYS

• Press to move the cursor along the text, one character

at a time.

• Press and hold to scan quickly through the text.

• Press

beginning or end of the text.

• When used in conjunction with certain function keys,

use

to select options.

• To insert characters into the text, use

and all other settings off.

first to produce

is set will give a lower case

CAPS

CLEAR

DEL

to move the cursor to the

again