Dymo LabelManager 100 사용자 설명서 - 페이지 4
{카테고리_이름} Dymo LabelManager 100에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Dymo LabelManager 100 6 페이지. Electronic labelmaker
Dymo LabelManager 100에 대해서도 마찬가지입니다: 사용 설명서 지침 (18 페이지)
페이지 인쇄
position the cursor under the character to the right of
the insertion point, then type in the characters required.
PRINTING
PRINT
• Press
to print the label.
PRINT
• Use cutter lever E to release the label – see page 2.
PREVIEW
Allows you to preview your label before printing it.
PREVIEW
• Press
+
and the entire text will scroll across
the display.
Note with a 2 line label, the message will be previewed as
a single line message.
SPACE KEY
• Press
to insert a space into the text.
FEED KEY
FEED
• Press
+
(1.37 inches) of blank tape
SYMBOLS
SYMBOL
• Press to select a symbol character – see 'Symbols and
special characters' and the symbols table on page 2.
TEXT SIZE
SIZE
• Press to display the symbols for the six text print sizes:
half-height, condensed
half-height, normal
half-height, extended
The cursor will be positioned over the current selection.
• Either press
to exit, or use
DEL
the cursor over the size symbol required, then press
or
to confirm the selection, or
SIZE
the selection and print the label.
VERTICAL TEXT
• Rotates the text through 90° so that the label is printed
indicator, top right of the display.
• Press again to cancel and return to horizontal text.
Note: Vertical text is not available on two-lines.
2-LINE PRINTING
• Press
to start the second line of text on a two-line
label. The two lines will be printed half-height and
ranged left, e.g.
This is a two
line label in the display will be
printed as:
This is a two
line label
to feed out 35mm
full height, condensed
full height, normal
full height, extended
or
to confirm
PRINT
VERT
+
BOX/UL
, as confirmed by the VERT
BOXED/UNDERLINED PRINTING
• Press
• Use
option and press
— indicator displayed.
• To return to previously selected Box/Underline text
press
ITALIC
• Press once to set italic text (confirmed by the ITALIC
indicator in the display).
Press again to cancel and return to normal text.
OUTLINE
• Press shift followed by "outline" to print the label in
outline text (confirmed by the OUTLINE indicator in the
display). Press shift and outline again to cancel and
return to normal text.
LABEL LENGTH
Displays the current label length. The length is normally
calculated automatically, according to the length of the
text on the label.
• Press
the length, or:
• Use
max.) or decrease the length in 2mm / 0.1 inch steps.
The display will flash if you try to make the label
shorter than the text.
to move
• If the length displayed is preceded by the > symbol, the
length has already been fixed; the label is too short for
the text and it will not print. Either press
increase the length in 2mm / 0.2 inch steps until the >
symbol disappears, or press
fixed length; the label is now long enough for the text
and can be printed.
• Press
confirmed by the LTH SET indicator in the display, or
• Press
• Pressing
and restore the automatic length.
MULTIPLE COPIES
• Your Labelmaker can provide multiple copies within the
range 1-99.
• To use this facility press
n = 1 on the display. To increase the number of copies
required press
backwards from 99. To print the desired quantity press
.
PRINT
4
once to display the menu below.
BOX/UL
A A
Normal
Underlined Box
text
around
or
to move the cursor under the desired
to enter. (Confirmed by the
.
DEL
ITALIC
OUTLINE
+
ITALIC
LENGTH
+
SIZE
to exit the length function without changing
DEL
or
to increase (400mm / 15.6 inches
to fix the length for all subsequent labels,
to fix the new length and print the label.
PRINT
CLEAR
+
will cancel the fixed length
DEL
COPIES
+
SYMBOL
. By pressing
BOX/UL
Shaded box
around
or
to
CLEAR
+
to cancel
DEL
COPIES
then
to show
SYMBOL
you can work