Dymo RhinoPRO 1000 사용자 설명서 - 페이지 4

{카테고리_이름} Dymo RhinoPRO 1000에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Dymo RhinoPRO 1000 5 페이지. Dymo rhino 1000: user guide
Dymo RhinoPRO 1000에 대해서도 마찬가지입니다: 빠른 참조 (2 페이지), 사용 지침 (2 페이지), 사용자 설명서 (11 페이지)

페이지 인쇄

MULTIPLE COPIES

• Your Labelmaker can provide multiple copies

within the range 1-99

• To use this facility press

to show n = 1 on the display. To increase the

number of copies required press

By pressing

you can work backwards

from 99.

To print the desired quantity press

Note: Labels will be printed with a short leader

and trailer. A row of vertical dots will print

between each label as a cutting guide; the final

label will have a long trailer ready for cutting.

INCREMENTAL NUMBERING

Labels can be printed in increments of 1-99

automatically.

• Key in your starting number as the right most

digit on the label. Press

the display will automatically move up a digit

to the next number. Press

to continue the sequence.

• It is also possible to include automatic

incremental numbering when printing

multiple copies.

• Key in your starting number, eg. LABEL 1 .

Next press

followed by

until the desired number of

copies are displayed eg.10.

Now press

ten labels - LABEL 1 to LABEL 10 .

• It is possible to print up to 99 sequentially

numbered labels at any one time.

Note: Labels are printed with short leaders and

trailers. See "multiple copies" above.

LAST LABEL MEMORY

• The unit will store the last label text and

settings when turned off. Upon power-up,

these will be restored and displayed.

Removal of the batteries for more than a few

seconds will cause this information to be lost.

Symbols and special characters

INTERNATIONAL CHARACTERS

To add a diacritical (accent) to create an

international character, enter the character first,

followed immediately by the diacritical, e.g. press

followed by

To add a diacritical to an existing character, use

to place the cursor under the

character to be changed, then press the

appropriate diacritical key.

COPIES

SYM

COPIES

then

SYM

then

COPIES

then

SYM

then

. This will print

then

to get

SYMBOLS

Press

SYM

characters, some of which are not available direct

from the keyboard. The display will show: A-L?

Each letter selects a line of symbol characters, as

shown in the table on page 2.

Press

DEL

'L' until you find the line of symbols required.

Use

to place the symbol in the label.

PRINT CONTRAST - May be adjusted by pressing

SYM

contrast symbols

• Use

print.

• Press

level will revert to the mid-setting when the

Labelmaker is turned off and on again.

Note: This function enables you to adjust the

print quality under extreme temperature

conditions.

Cleaning

• Clean the cutter blade regularly: Remove the

cassette, then insert the tip of a ball pen or

pencil between L-shaped piece

guide pin – see page 2.

• Press and hold down cutter lever

expose cutter blade

and alcohol to clean both sides of the blade.

Release cutter lever

• Check and clean print head face

using a cotton bud and alcohol ONLY.

Troubleshooting

No display

• check machine is on

• replace discharged batteries

• check AC adaptor.

No printing or poor text

• replace discharged batteries

• check tape cassette installed correctly

• clean the print head

• replace the tape cassette.

Tape jammed

• lift out tape cassette carefully

• remove/release jammed tape

• DO NOT cut the ink ribbon – turn spool to

tighten

• cut off excess label tape

• refit/replace the tape cassette.

Poor cutter performance

• clean the cutter blade regularly

to show symbols and special

to cancel, or press a letter key 'A' to

to select a symbol. Press

followed by

to display the five

to select lighter or darker

to confirm the setting. The contrast

D ,

then use a cotton bud

Continued overleaf.

and the

regularly