ADEMCO Ademco VISTA-20P 프로그래밍 매뉴얼 - 페이지 2

{카테고리_이름} ADEMCO Ademco VISTA-20P에 대한 프로그래밍 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ADEMCO Ademco VISTA-20P 17 페이지. Programming auto arming and disarming schedules
ADEMCO Ademco VISTA-20P에 대해서도 마찬가지입니다: 빠른 설치 매뉴얼 (2 페이지), 사용자 설명서 (20 페이지), 프로그래밍 매뉴얼 (17 페이지), 빠른 시작 매뉴얼 (6 페이지), 빠른 설치 매뉴얼 (2 페이지), 빠른 설치 매뉴얼 (2 페이지), 프로그래밍 매뉴얼 (2 페이지), 빠른 매뉴얼 (2 페이지)

페이지 인쇄

TO ENTER PROGRAMMING MODE (using an alpha keypad connected to the control):

A. POWER UP, then press [ ✱ ] and [#] at the same time, within 50 seconds of powering up (this method must be used if ✱ 98

was used to exit program mode). OR

B. Initially, key: Installer Code (4 + 1 + 1 + 2) plus 8 + 0 + 0.

PROGRAMMING MODE COMMANDS

Task

Go to a Data Field

Entering Data

Review a Data Field

Deleting an Entry

Initialize Download ID

Reset Factory Defaults

Zone Programming

Function Key Programming Press ∗ ∗ ∗ ∗ 57. Unlabeled keypad keys (known as ABCD keys) for special functions

Zone Programming

(Expert Mode)

Output Device Mapping

Output Programming

Zone List Programming

Alpha Programming

Exit Program Mode with

installer code lockout

Exit Program Mode

SPECIAL MESSAGES

OC = OPEN CIRCUIT (no communication between Keypad and Control).

EE or ENTRY ERROR = ERROR (invalid field number entered; re-enter valid field number).

After powering up, AC, dI (disabled) or Busy Standby and NOT READY will be displayed after approximately 4 seconds.

This will revert to a "Ready" message in approximately 1 minute, which allows PIRS, etc. to stabilize. You can bypass this

delay by pressing [#] + [0].

If E4 or E8 appears, more zones than the expansion units can handle have been programmed. The display will clear after

you correct the programming.

TABLE OF DEVICE ADDRESSES

This Device

RF Receiver

AUI 1

AUI 2

Long Range Radio

4286 Voice Module

Zone Expanders (4219/4229):

module 1 (for zones 09 - 16)

module 2 (for zones 17 - 24)

module 3 (for zones 25 - 32)

module 4 zones 33 - 40

module 5 zones 41 - 48

Relay Modules (4204):

module 1

module 2

module 3

module 4

Keypads:

keypad 1

keypad 2

keypad 3

keypad 4

keypad 5

keypad 6

keypad 7

keypad 8

5800TM Module

** These module addresses apply to VISTA-20P only.

†† Addressable devices are identified by "1" plus the device address when reporting. Enter report code for zone 91 to enable addressable device

reporting (default = reports enabled). See field *199 for addressable device (ECP) 3-digit/2-digit identification keypad display options.

Command/Explanation

Press [∗ ∗ ∗ ∗ ] + [Field Number], followed by the required entry.

When the desired field number appears, simply make the required entry. When the last entry

for a field is entered, the keypad beeps three times and automatically displays the next data

field in sequence. If the number of digits that you need to enter in a data field is less than the

maximum digits available (for example, the phone number fields *41, *42), enter the desired

data, then press [∗ ] to end the entry. The next data field number is displayed.

Press [#] + [Field Number].

Data will be displayed for that field number. No changes will be accepted in this mode.

Press [∗ ∗ ∗ ∗ ] + [Field Number] + [∗ ∗ ∗ ∗ ]. (Applies only to fields ∗40 thru *46, *94, and pager fields)

Press ∗ ∗ ∗ ∗ 96. Initializes download ID and subscriber account number.

Press ∗ ∗ ∗ ∗ 97. Sets all data fields to original factory default values.

Press ∗ ∗ ∗ ∗ 56. Zone characteristics, report codes, alpha descriptors, and serial numbers for 5800

RF transmitters.

Press ∗ ∗ ∗ ∗ 58. Same options as *56 mode, but with fewer prompts. Intended for those familiar

with this type of programming, otherwise *56 mode is recommended.

Press ∗ ∗ ∗ ∗ 79. Assign module addresses and map individual relays/powerline carrier devices

Press ∗ ∗ ∗ ∗ 80. 4229 or 4204 Relay modules, Powerline Carrier devices, or on-board triggers

Press ∗ ∗ ∗ ∗ 81. Zone Lists for relay/powerline carrier activation, chime zones, pager zones, etc.

Press ∗ ∗ ∗ ∗ 82. Zone alpha descriptors

Press ∗ ∗ ∗ ∗ 98. Exits programming mode and prevents re-entry by: Installer Code + 8 + 0 + 0.

To reenter programming mode, the system must be powered down, then powered up. Then

use method A above. See field *88 for other *98 Program mode lockout options.

Press ∗ ∗ ∗ ∗ 99. Exits programming mode and allows re-entry by: Installer Code + 8 + 0 + 0 or

method A above.

Uses Address Reports as ††

100

101

102

103

104

107

108

09**

109

10**

110

11**

111

112

113

14**

114

15**

115

n/a

Enabled By...

*56 zone programming: input device type entry

Automatic if AUI enable field *189 enabled for AUI 1

Automatic if AUI enable field *189 enabled for AUI 2

automatic if output to long range radio field *29 enabled

automatic if phone module access code field *28 enabled

*56 zone programming: input device type entry, then:

automatic if zone no. 9-16 entered as AW type or relay assigned

automatic if zone no. 17-24 entered as AW type or relay assigned

automatic if zone no. 25-32 entered as AW type or relay assigned

automatic if zone no. 33-40 entered as AW type or relay assigned

automatic if zone no. 41-48 entered as AW type or relay assigned

*79 output device programming: device address prompt:

entered at device address prompt

data field programming as listed below:

always enabled, all sounds enabled.

data field *190

data field *191

data field *192

data field *193

data field *194

data field *195

data field *196

automatic

– 2 –