ADEMCO Ademco VISTA-20P 프로그래밍 매뉴얼 - 페이지 8

{카테고리_이름} ADEMCO Ademco VISTA-20P에 대한 프로그래밍 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ADEMCO Ademco VISTA-20P 17 페이지. Programming auto arming and disarming schedules
ADEMCO Ademco VISTA-20P에 대해서도 마찬가지입니다: 빠른 설치 매뉴얼 (2 페이지), 프로그래밍 매뉴얼 (17 페이지), 사용자 설명서 (20 페이지), 빠른 시작 매뉴얼 (6 페이지), 빠른 설치 매뉴얼 (2 페이지), 빠른 설치 매뉴얼 (2 페이지), 프로그래밍 매뉴얼 (2 페이지), 빠른 매뉴얼 (2 페이지)

페이지 인쇄
ADEMCO Ademco VISTA-20P 프로그래밍 매뉴얼

Configurable Zone Types Worksheets

Configurable zone types 90 and 91 can be programmed via downloader software or from a keypad using data
fields*182-*185. Configurable zone types 92 and 93 (VISTA-20P only) can only be programmed using the
downloader software.
Programming Configurable Zone Type options involves entering 10 digits in data field *182 for zone type 90 and
field *184 for zone type 91, where each digit represents the sum of the values of its various options as shown in
the tables below. Use fields *183 and *185 to program Contact ID report codes for these zone types.
DIGIT 1
(See note 5 for RF zones)
Response when system disarmed and zone is:
Intact EOL
Open
RF zone normal
RF zone N/A
0 = normal
0 = normal
1 = alarm
4 = alarm
2 = trouble
8 = trouble
3 = fault
12 = fault
Digit 1 = EOL + Open
DIGIT 3
(See note 5 for RF zones)
Response when armed STAY and zone is:
Intact EOL
Open
RF zone normal
RF zone N/A
0 = normal
0 = normal
1 = alarm
4 = alarm
2 = trouble
8 = trouble
3 = fault
12 = fault
Digit 3 = EOL + Open
DIGIT 5
(See note 5 for RF zones)
Response when armed AWAY and zone is:
Intact EOL
Open
RF zone normal
RF zone N/A
0 = normal
0 = normal
1 = alarm
4 = alarm
2 = trouble
8 = trouble
3 = fault
12 = fault
Digit 5 = EOL + Open
DIGIT 7
Display Faults
Power Reset/
Verification
0 = show alarms
0 = no
when armed
4 = power reset
& disarmed
after fault
(by code + OFF)
1 = don't show
12 = verification
alarms when
(see zone
armed
(show
type 16)
alarms, trbles,
faults when
disarmed)
3 = never show
any alarms,
trbles, faults
Digit 7 = fault display + power
reset/verification
DIGIT 9
Alarm Sounds
Use Bell
Timeout
0 = none
0 = no
1 = steady
4 = yes
keypad
2 = steady bell
see fields *32,
and keypad
*33
3 = pulsing bell
and keypad
Digit 9 = alarm sounds + bell timeout + fire zone
DIGIT 2
(See note 5 for RF zones)
Auto
Restore
Shorted
RF zn off-normal
0 = normal
0 = no
1 = alarm
4 = yes
2 = trouble
3 = fault
Digit 2 = Short + auto restore + vent zone
DIGIT 4
(See note 5 for RF zones)
Byp. when
disarmed
Shorted
RF zn off-normal
0 = normal
0 = no
1 = alarm
4 = yes
2 = trouble
3 = fault
Digit 4 = Short + byp. disarmed + byp. armed
DIGIT 6
(See note 5 for RF zones)
Dial Delay
(see field *50)
Shorted
RF zn off-normal
0 = normal
0 = no
1 = alarm
4 = use delay
2 = trouble
3 = fault
Digit 6 = Short + dial delay + fault delay
DIGIT 8
Use Entry
Use Exit
Delay 1/2
Delay
0 = no
0 = no
1 = delay 1
4 = use exit
2 = delay 2
delay
Digit 8 = entry delay 1/entry delay 2 + exit delay +
interior zone type
DIGIT 10
Respond as
Trouble
Fire Zone
Sounds
0 = no
0 = none
8 = yes
1 = periodic
beep
see zone type
2 = trouble
09; see note 4
beeps
Digit 10 = trouble sounds + chime
Digit
Vent Zone
1
2
0 = no
8 = yes
3
4
5
6
7
8
Byp. when
9
armed
10
0 = no
To calculate each digit's entry:
8 = yes
Simply add the values of the selected options
in each of the digit's columns (one option per
column). For example, to program Digit 2 for
"alarm response to short," "auto restore on,"
but not a "vent zone," enter 5 ("1" for alarm
short + "4" for auto restore yes + "0" for vent
Fault Delay
zone no).
(see field *87)
0 = no
8 = use delay
see note 1
NOTES:
Respond as
1. Do not use the "fault delay" option with a
Interior Type
0 = no
8 = yes
see note 2
2. To create an interior type zone, select
3. Do not set fire zones to respond as a
4. 4219/4229 modules must use EOLRs or
5. RF Zones: The "open" option in digits 1,
Chime when
Chime Mode On
0 = no
4 = yes
6. Zone-Doubling/Double-Balanced: A short
– 8 –
Entries for Fields *182 and *184
Zone Type 90
Zone Type 91
(field *182)
(field *184)
INTACT
OPEN
SHORTED
EOL
-018-V0
Zone Conditions Represented
in Digits 1-6
configurable zone type if it is set for an
entry or exit delay, otherwise
unpredictable results may occur.
"respond as interior zone type" (Digit 8,
interior type = yes), and set zone
response to "fault" in digits 3-4 to ensure
fault displays; do not set as "normal,"
"alarm," or "trouble."
"fault" (digits 1-6), otherwise faults will not
display unless the [∗] key is pressed.
unpredictable results may occur.
3, and 5 is not applicable for RF zones.
Use the "intact EOL" option for normal RF
zone conditions and "shorted" for off-
normal RF zone conditions.
on either zone of a zone-doubled pair or
on a double-balanced zone causes a
tamper condition.