ADEMCO LYNX 사용자 설명서 - 페이지 5
{카테고리_이름} ADEMCO LYNX에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. ADEMCO LYNX 17 페이지.
ADEMCO LYNX에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (8 페이지), 시스템 매뉴얼 (14 페이지)
페이지 인쇄
Field
Function
43
PRIMARY SUBS ACCT #
SECONDARY SUBS ACCT #
44
47
PHONE SYSTEM SELECT
48
REPORT FORMATfor PRIM./SEC.
0 = 3+1, 4+1 ADEMCO L/S STANDARD
1 = 3+1, 4+1 RADIONICS STANDARD
2 = 4+2 ADEMCO L/S STANDARD
3 = 4+2 RADIONICS STANDARD
49
SPLIT/DUAL REPORTING
** Pager Message
A 7-digit code (plus optional 16-digit prefix) is
sent to the pager consisting of a 3-digit event code,
followed by 00 and a 2-digit user or zone number.
See Installation Instructions for an explanation of
the pager code, which takes the following form:
AAAAAAAAAAAAAAAA-EEE-00NN
Where: AAA...
= optional 16 digits (see field *88)
EEE = 3-digit event code: 911 (alarm), 101 (open), 102 (close), 811 (trouble)
00
= always displayed
NN
= 2-digit user number or zone number depending on type of event (EEE) that occurred
50
15 SEC DIALER DELAY (BURG)
PERIODIC TEST REPORT
51
52
FIRST TEST REPORT OFFSET
SESCOA/RADIONICS SELECT
53
ZONE PROGRAMMING
56
RF JAM DETECT
58
† Entry of a number other than one specified will give unpredictable results.
Programmed Values
† [1]
If Cent. Sta. IS NOT on a WATS line: 0 = Pulse Dial; 1 = Tone
Dial; if Cent. Sta. IS on a WATS line: 2 = Pulse Dial ; 3 = Tone
[7, 0]
Primary
Secondary
[0]
0 = Disable (Backup report only)
TO PRIMARY PHONE No.
1 = Alarms, Restore, Cancel
2 = All except Open/Close, Test
3 = Alarms, Restore, Cancel
4 = All except Open/Close, Test
5 = A l l
TO PRIMARY PHONE No.
6 = All except Open/Close
7 = All reports
8 = All reports
9 = All except Open/Close
† [0]
0 = no; 1 = yes; UL installations = 0
† [0]
0 = none; 1 = 24 hours; 2 = weekly; 3 = 30 days (enter Test Code
in field * 64)
† [2]
0 = 24 hour; 1 = 6 hours; 2 = 12 hours; 3 = 18 hours (Time to 1st
report from power up/programming or downloading).
[0]
0 = Radionics (0–9, B–F reporting); 1 = SESCOA (0–9 only
reporting). Select 0 for all other formats.
See procedure later in this form and refer to the Inst. Instr.
[0]
0 = no RF Jam Detection; 1 = RF Jam Detect on, no CS report;
2 = RF Jam Detect on with CS report (if trouble/restore report is
enabled in fields *60, *71)
5 –
–
[
] = Table 1 Default Value
See note on previous page
See note on previous page
6 or undefined = 4+2 ADEMCO EXPRESS
7 = ADEMCO CONTACT ID REPORTING
8 = 3+1, 4+1 ADEMCO L/S EXPANDED
9 = 3+1, 4+1 RADIONICS EXPANDED
TO SECONDARY PHONE No.
Others
Open/Close, Test
A l l
A l l
A l l
TO PAGING** No. (Secondary)
Alarms, Open/Close ‡ , Troubles
Alarms, Troubles
Alarms, Open/Close ‡ , Troubles
Open/Close ‡
‡ Will report users 5-8 or wireless
arm/disarm button zones
26-33; all other zones and
users do not report