GREAT PLANES AT-6 Texan 사용 설명서 - 페이지 3

{카테고리_이름} GREAT PLANES AT-6 Texan에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. GREAT PLANES AT-6 Texan 20 페이지. Legendary warbirds custom-wood series

페이지 인쇄

1. Balance Your Model (Cg)

Note: We, as the kit manufacturer, provide you with a top quality

kit and great instructions, but ultimately the quality of your

finished model depends on how you build it; therefore, we cannot

in any way guarantee the performance of your completed model,

and no representations are expressed or implied as to the

performance or safety of your completed model.

Please inspect all parts carefully before starting to build! If

any parts are missing, broken or defective, or if you have any

questions about building or flying this airplane, please call us

at (217) 398-8970. You can also check our web site at

www.greatplanes.com for the latest AT-6 ARF updates, or

e-mail your questions to [email protected]. If

you are calling for replacement parts, please reference the

part numbers and the kit identification number (the small

sticker on the end of the carton) and have them ready when

calling.

DECISIONS YOU MUST MAKE

Engine Selection

There are several engines that will work well in your AT-6 ARF. We

recommend a 2-stroke such as an O.S.

O.S. .46 FX, or the SuperTigre

realistic sound, an O.S. FS-52 4-stroke can't be beat.

Required Accessories

Items in parentheses (GPMQ4243) are suggested part numbers

recognized by distributors and hobby shops and are listed for

your ordering convenience. GPM is the Great Planes

TOP is the Top Flite

brand, and HCA is the Hobbico

Four-channel Radio With Five Servos

Engine – See Engine Selection Above

Propeller (Top Flite

Power Point

Instructions For Proper Size)

Medium Fuel Tubing (GPMQ4131)

6" Servo Extension (1)

"Y" connector (1) when using a basic 4-channel radio

Slimline Sport Scale muffler

Building Supplies & Tools

These are the building tools that are required. We recommend

Great Planes Pro

™

CA and Epoxy glue.

2 oz. Pro CA (Thin, GPMR6003)

2 oz. Pro CA+ (Medium, GPMR6009)

6-Minute Pro Epoxy (GPMR6045)

30-Minute Pro Epoxy (GPMR6047)

Epoxy Brushes (GPMR8060)

Pro Thread Locking Compound (GPMR6060)

T-pins (HCAR5150)

Adjustable Wrench

Plastic Wrap or Waxed Paper

Isopropyl Alcohol (70%)

.40 LA, O.S. .40 FX, or

G40. For unsurpassed power and

brand.

–Refer To Your Engine's

Mixing Sticks (GPMR8055)

Round Toothpicks

Hobby Knife (TOWR1010), #11 Blades (TOWR1015)

Small Hobby Clamps

String

Builders Triangle Set (HCAR0480)

Masking Tape (TOPR8018)

Sandpaper (coarse, medium, fine grit)

Easy-Touch

™

1/4" Latex Foam Rubber Padding (HCAQ1000)

Paper Towels

Felt-Tip Marker

Wire Cutter

File

Drill Bits: 1/16" (1.5mm), 5/64" (2mm), 3/32" (2.4mm),

1/8" (3mm), 3/16" (4.7mm), 1/4" (6mm)

Optional Supplies & Tools

CA Applicator Tips (HCAR3780)

CA Debonder (GPMR6039)

Sealing Iron (TOPR2100)

Heat Gun (TOPR2000)

Single-edge Razor Blades (HCAR0312)

Curved Tip Canopy Scissors For Trimming Plastic Parts

(HCAR0667)

Switch and Charge Jack (GPMM1000)

Fuel Filler Valve (GPMQ4160)

Optional Retract Items

brand,

Hobbico Mechanical Retracts Main (HCAP4010)

Retract servo (compatible with your radio system)

Threaded pushrods (2) (GPMQ3750)

Nylon Clevis (2) (GPMQ3800)

Wheel Collars (2) (GPMQ4306)

1-1/4" x 5/32" Axle (GPMQ4280)

General Inspection

Remove the fuselage, wing panels, rudder assembly and

stabilizer assembly from their bags. Inspect all items closely to

check for any damage. If any of the control surfaces are

attached, simply pull them apart and store the hinges in a safe

place until it is time to reattach them. The manual begins with

all the surfaces shown separated.

Your AT-6 is covered with high quality Top Flite MonoKote

covering. If any of the covering has loosened, use a heat gun

or sealing iron to tighten it.

Several times during construction we refer to the "top" or

"bottom" of the model or a part of the model. It is understood

that the "top" or "bottom" of the model is as it would be when

the airplane is right side up and will be referred to as the "top"

even if the model is being worked on upside-down.

Bar Sander (GPMR6170, or similar)