GREAT PLANES AT-6 Texan Руководство по эксплуатации - Страница 3
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Игрушка GREAT PLANES AT-6 Texan. GREAT PLANES AT-6 Texan 20 страниц. Legendary warbirds custom-wood series
Печатать страницу
Note: We, as the kit manufacturer, provide you with a top quality
kit and great instructions, but ultimately the quality of your
finished model depends on how you build it; therefore, we cannot
in any way guarantee the performance of your completed model,
and no representations are expressed or implied as to the
performance or safety of your completed model.
Please inspect all parts carefully before starting to build! If
any parts are missing, broken or defective, or if you have any
questions about building or flying this airplane, please call us
at (217) 398-8970. You can also check our web site at
www.greatplanes.com for the latest AT-6 ARF updates, or
e-mail your questions to [email protected]. If
you are calling for replacement parts, please reference the
part numbers and the kit identification number (the small
sticker on the end of the carton) and have them ready when
calling.
DECISIONS YOU MUST MAKE
Engine Selection
There are several engines that will work well in your AT-6 ARF. We
recommend a 2-stroke such as an O.S.
O.S. .46 FX, or the SuperTigre
realistic sound, an O.S. FS-52 4-stroke can't be beat.
Required Accessories
Items in parentheses (GPMQ4243) are suggested part numbers
recognized by distributors and hobby shops and are listed for
your ordering convenience. GPM is the Great Planes
TOP is the Top Flite
®
brand, and HCA is the Hobbico
Four-channel Radio With Five Servos
Engine – See Engine Selection Above
Propeller (Top Flite
®
Power Point
Instructions For Proper Size)
Medium Fuel Tubing (GPMQ4131)
6" Servo Extension (1)
"Y" connector (1) when using a basic 4-channel radio
Slimline Sport Scale muffler
Building Supplies & Tools
These are the building tools that are required. We recommend
Great Planes Pro
™
CA and Epoxy glue.
2 oz. Pro CA (Thin, GPMR6003)
2 oz. Pro CA+ (Medium, GPMR6009)
6-Minute Pro Epoxy (GPMR6045)
30-Minute Pro Epoxy (GPMR6047)
Epoxy Brushes (GPMR8060)
Pro Thread Locking Compound (GPMR6060)
T-pins (HCAR5150)
Adjustable Wrench
Plastic Wrap or Waxed Paper
Isopropyl Alcohol (70%)
®
.40 LA, O.S. .40 FX, or
®
G40. For unsurpassed power and
®
®
brand.
®
–Refer To Your Engine's
Mixing Sticks (GPMR8055)
Round Toothpicks
Hobby Knife (TOWR1010), #11 Blades (TOWR1015)
Small Hobby Clamps
String
Builders Triangle Set (HCAR0480)
Masking Tape (TOPR8018)
Sandpaper (coarse, medium, fine grit)
Easy-Touch
™
1/4" Latex Foam Rubber Padding (HCAQ1000)
Paper Towels
Felt-Tip Marker
Wire Cutter
File
Drill Bits: 1/16" (1.5mm), 5/64" (2mm), 3/32" (2.4mm),
1/8" (3mm), 3/16" (4.7mm), 1/4" (6mm)
Optional Supplies & Tools
CA Applicator Tips (HCAR3780)
CA Debonder (GPMR6039)
Sealing Iron (TOPR2100)
Heat Gun (TOPR2000)
Single-edge Razor Blades (HCAR0312)
Curved Tip Canopy Scissors For Trimming Plastic Parts
(HCAR0667)
Switch and Charge Jack (GPMM1000)
Fuel Filler Valve (GPMQ4160)
Optional Retract Items
brand,
Hobbico Mechanical Retracts Main (HCAP4010)
Retract servo (compatible with your radio system)
Threaded pushrods (2) (GPMQ3750)
Nylon Clevis (2) (GPMQ3800)
Wheel Collars (2) (GPMQ4306)
1-1/4" x 5/32" Axle (GPMQ4280)
General Inspection
Remove the fuselage, wing panels, rudder assembly and
stabilizer assembly from their bags. Inspect all items closely to
check for any damage. If any of the control surfaces are
attached, simply pull them apart and store the hinges in a safe
place until it is time to reattach them. The manual begins with
all the surfaces shown separated.
Your AT-6 is covered with high quality Top Flite MonoKote
covering. If any of the covering has loosened, use a heat gun
or sealing iron to tighten it.
Several times during construction we refer to the "top" or
"bottom" of the model or a part of the model. It is understood
that the "top" or "bottom" of the model is as it would be when
the airplane is right side up and will be referred to as the "top"
even if the model is being worked on upside-down.
3
Bar Sander (GPMR6170, or similar)
Building Notes
®